5-Button 2-Way LED
Remote Start Systems
QUICK START
OPERATION GUIDE
5-Button 2-Way LED
Remote Start Systems
QUICK START
OPERATION GUIDE
REMOTE START FUNCTIONS
FUNCTION
BUTTON(S)
LED CONFIRMATION
NOTE
Engine Start/Stop
x 2
Flash + Melody
Remote LED’s will flash to indicate remaning run time. 4 = 76-100% , 3 = 51-75%, 2 = 26-50%, 1 = 1-15%.
The controller will beep when only 1 minute is remaining as an expiration warning.
Run Time Extender
2
All 4 LED’s will flash
All 4 LED’s will flash to indicate restarting of the run timer (only allowed once per remote start cycle).
Low Battery & Low/
Hi Temp Auto-Start
, ,
1 Beep
Auto-start will activate a max of once per 2 hours and cancels when the ignition key is turned ON. See
your installer or the full manual for threshold settings.
Cabin Temperature
P
,
1-4 LEDs Flash + Melody
4 = Over 90F , 3 = 61-90F, 2 = 31-60F, 1 = Under 30F.
Remote Valet
2
, ,
+
Melody
This disables remote start and the security system. The status LED will turn on. Repeat this process or
press valet button once to exit valet mode.
FUNCTION
VALET BUTTON
NOTE
Pit Stop Mode
2
Press 2x w/ Engine On For More Than 10 Sec.
(6x for XL mode)
This will leave the engine running for the programmed run time (XL mode runs for 12 hours) so you can
take your keys with you to run errands.
OTHER 2-WAY CONTROLLER FUNCTIONS
FUNCTION
BUTTON(S)
LED
CONFIRMATION
NOTE
Status Update
3
P
,
or Flash
This confi rms the current Lock/Unlock
status of the system/vehicle.
CAR 2 Mode
P
,
Flash + 2 Beeps
To control a 2nd vehicle. Repeat to return
to CAR 1 mode ( + 1 Beep).
Low Car
Battery Alert
-
4 Beeps
Alerts when battery level is below 11.5v
for over 30 seconds.
Out Of Range
-
All LED’s Flash
When command response is not received
P
,
+
Flash
CH3/AUX1
3
- Write Function In Function
Column
P
x 2 ,
+
Flash
CH4/AUX2
3
- Write Function In Function
Column
P
x 3 ,
+
Flash
CH5/AUX3
3
- Write Function In Function
Column
+
+
Flash
AUX4
3
- Write Function In Function Column
2-WAY OPTIONS
FEATURE
PROCEDURE
Beep Volume
Hold
P
+
for 1 second.
Button Lock
Hold
P
+
for 1 second.
TIP
: If your system stops responding to your remote, make sure
your aren’t accidentally in the wrong “Car” profi le.
TROUBLE SHOOTING TIP: If remote start won’t activate,
the system may be in valet mode (Status LED ON). Press
the valet button once to exit.
Status LED
Valet / Programming Button
WINDOW-MOUNT ANTENNA/RECEIVER
3
2
MANUAL TRANSMISSION RESERVATION MODE
2
This must be performed before you can remote start a manual transmission vehicle to ensure the car is in neutral &
maximum safety. Consult your installer for more information.
1) With the engine running by key (more than 10 seconds), hold the brake pedal & place the transmission in neutral.
2) Apply the parking brake and release the brake pedal.
3) Send the remote start command via your remote. The remote start should engage (LED flashing).
4) Take the ignition key out of the switch (the engine should stay running).
5) Exit the vehicle and lock your doors with the remote. The engine will turn off.
Scan to register
& download the
full operation
guide at
CarAlarm.com!
2-These functions are only available on some remote start models. Consult your installer for more info.
3-These special functions may not be available on your vehicle. Consult your installer.
