Exalt EX i GigE Series Installation And Management Manual Download Page 74 | Manualshive

Page: 74 / 133

background image

Exalt Installation and Management Guide

EX-i Series FDD Digital Microwave Radios

66

202675-005

2011-08-30

Alarms Page

This page provides an easy-to-read summary of the alarm status of both local and remote radios. The

colors on this page reflect the color of the alarms displayed on the radio front panel. However,

additional detail displays on this page to aid in quick assessment of issues and status.

Figure 46 Alarms page

Table 5 lists alarm status conditions that appear on this page.

Table 5 Alarm status indicators

Label

Status

Link System

Indicates RF link status:
• Green Solid = Error-free connection (BER<10e-6)
• Yellow Solid = Errored connection (10e-3>BER >10e-6)
• Red Solid = No link (BER>10e-3)

RX Alarm

When Rx RSL Differential is enabled, provides alarms for Space Diversity configurations.
• Green Solid = The Rx values of the two receivers are within 5dB of the programmed

differential value.

• Yellow Solid = The Rx values of the two receivers are further apart than 5dB of the

programmed differential value.

«
...
72
73
74
75
76
...
»

Summary of Contents for EX i GigE Series






































































































































Reviews:

No comments

Related manuals for EX i GigE Series

Brand: Icom Pages: 15

Brand: ICP DAS USA Pages: 4

Brand: ICP DAS USA Pages: 21

Brand: ICP DAS USA Pages: 6

Brand: Ham International Pages: 25

Brand: Roberts Pages: 40

Brand: Diga-Talk2 Pages: 15

PD60 UL913 Series

Brand: Hytera Pages: 37

Brand: Radio Shack Pages: 12

Brand: Radio Shack Pages: 16

Brand: Enrock Marine Pages: 2

Brand: Sangean Pages: 24

Brand: Anysecu Pages: 4

Brand: Retevis Pages: 10

Brand: Ascot Pages: 40

X-tra talk LXT560 series

Brand: Midland Pages: 1

Brand: Sangean Pages: 151

Brand: Emerson Pages: 1

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands