manualshive.com logo in svg

Exabyte VXA-2 AUTOPAK1X7, Product Manual, Page: 75 / 104

Share
Download
Exabyte VXA-2 AUTOPAK1X7 Product Manual Download Page 75

O

CTOBER

 2002

E

XABYTE

 VXA-2 A

UTO

P

AK1x7

 

A

UTOLOADER

67

E

RROR

 C

ODES

E

RROR

 C

ODES

This section describes the error codes that appear on the autoloader’s operator 

panel and provides corrective actions.

Table 6-1

 lists the autoloader error codes in numerical order.

Caution

Most autoloader components can be replaced only by Exabyte-approved service 

providers.  If you cannot find an obstruction or other obvious cause for the 

problem, contact your service provider.  Unless you have a self-maintenance 

contract, do not attempt to replace any components. If you do, you will void your 

warranty.

Important

Some corrective actions advise you to reset the autoloader.  

Before resetting, make sure there is no SCSI activity on the 

SCSI bus, so you do not disrupt communications.

Table 6-1

Autoloader error codes 

Code

Description

Corrective action

10

Dropped a tape

. The robot 

dropped a cartridge.

CAUTION:

 Do not try to put the cartridge back in the robot 

picker. 

!

Put the cartridge back in the magazine if you know where 

it belongs.

!

Make sure the autoloader is not being used by any host, 

then reset the autoloader from the operator panel. If 

necessary, power the autoloader off and back on to reset 

the tape drive.

!

If the error persists, contact your service provider.

11

Source empty

. There is no 

cartridge in the source location.

Install a cartridge in the source location or redirect the robot 

to another location. 

12

Dest full

. A cartridge already 

exists in the destination location.

Remove the cartridge from the destination or redirect the 

robot to another location.

13

Put failure

. The robot could not 

place a cartridge because of 

mechanical problems.

!

Make sure there is nothing blocking the robot or the tape 

drive.

!

Make sure the autoloader is not being used by any host, 

then reset the autoloader from the operator panel. If 

necessary, power the autoloader off and back on to reset 

the tape drive.

!

If the error persists, contact your service provider.

14

Pick failure

. The robot could not 

pick a cartridge because of 

mechanical problems.

Summary of Contents for VXA-2 AUTOPAK1X7









































































































Reviews:

No comments