EWM Taurus **5 Basic S Series Operating Instructions Manual Download Page 18 | Manualshive

Page: 18 / 41

EWM Taurus **5 Basic S Series Operating Instructions Manual Download Page 18

Design and function

Transport and installation

18

099-005589-EW501

20.03.2019

5

Design and function

WARNING

Risk of injury from electrical voltage!
Contact with live parts, e.g. power connections, can be fatal!

• Observe the safety information on the first pages of the operating instructions!
• Commissioning must be carried out by persons who are specifically trained in handling

power sources!

• Connect connection or power cables while the machine is switched off!

CAUTION

Risk from electrical current!
If welding is carried out alternately using different methods and if a welding torch and
an electrode holder remain connected to the machine, the open-circuit/welding voltage
is applied simultaneously on all cables.

• The torch and the electrode holder should therefore always be placed on an insulated

surface before starting work and during breaks.

Read and observe the documentation to all system and accessory components!

5.1

Transport and installation

CAUTION

Risk of accidents due to supply lines!
During transport, attached supply lines (mains leads, control cables, etc.) can cause
risks, e.g. by causing connected machines to tip over and injure persons!

• Disconnect all supply lines before transport!

5.2

Scope of delivery

The delivery is checked and packaged carefully before dispatch, however it is not possible to exclude the
possibility of damage during transit.

Receiving inspection

• Check that the delivery is complete using the delivery note!

In the event of damage to the packaging

• Check the delivery for damage (visual inspection)!

In the event of complaints

If the delivery has been damaged during transport:
• Please contact the last haulier immediately!
• Keep the packaging (for possible checking by the haulier or for the return shipment).

Packaging for returns

If possible, please use the original packaging and the original packaging material. If you have any queries
on packaging and protection during transport, please contact your supplier.

«
...
16
17
18
19
20
...
»

Summary of Contents for Taurus **5 Basic S Series










































Reviews:

No comments