background image

 
 
 
 
 
 

General instructions 

 

 

 WARNING 

 

Read the operating instructions! 
The operating instructions  provide an introduction  to the safe use  of the products.  

•  Read  and observe  the operating  instructions for  all system components, especially the 

safety instructions and  warning  notices! 

•  Observe  the accident prevention  regulations  and any regional  regulations! 
•  The  operating  instructions must be kept at the site of operation. 
•   Safety and warning  labels at the machine indicate any possible risks.  

Keep  these labels  clean and  legible  at all times. 

•  The  machine has been constructed to the state of the art and any regulations  and 

standards  applicable.  It may be operated,  serviced  and  repaired  by

 

trained  personnel  only. 

 

 

 

In  the event  of queries  on installation,  commissioning,  operation  or special  conditions  at  the 
installation  site,  or on usage,  please  contact  your  sales  partner  or our  customer  service 
department  on +49  2680  181-0. 
A list  of  authorised  sales  partners  can be  found at  www.ewm -group.com. 

 

Liability relating  to the  operation  of  this equipment  is restricted solely to the function  of the 
equipment.  No other  form  of  liability, regardless  of  type, shall be accepted.  This  exclusion of 
liability shall be deemed  accepted  by the user  on commissioning  the  equipment.  
The  manufacturer  is unable  to monitor  whether  or  not these instructions  or the conditions  and 
methods  are  observed  during  installation,  operation,  usage  and  maintenance  of  the equipment. 
An incorrectly  performed  installation  can result in material  damage  and  injure  persons  as a 
result. For  this reason,  we  do  not accept any responsibility  or  liability for  losses, damages  or 
costs arising  from  incorrect  installation,  improper  operation  or  incorrect  usage  and  maintenance 
or  any actions connected  to this in any  way. 
 
 
 
 
 
 

© EWM AG 
Dr. Günter-Henle-Str.  8 

D-56271  Mündersbach,  Germany 

 

The  copyright  to this document  remains  the  property  of  the manufacturer.  
Reprinting,  including  extracts, only permitted  with  written  approval. 
The  content of  this document  has been  prepared  and  reviewed  with  all reasonable  care. The  information 
provided  is subject to change,  errors  excepted. 

Summary of Contents for cool50-2 U40



























Reviews: