background image

5. Installation

DEPOLOX® 400 M

50

EN

5.15 Initial commissioning

Following complete mechanical and electrical
installation, initial commissioning can be car-
ried out. Please check that the following con-
ditions are met:

Electronics module, flow cell or Y-style 
flow-through assembly are installed.

Housing  covers  are  fitted.

Optional strainer is installed.

Sample water inlet and outlet are connec-
ted.

Sensors are installed in the flow cell or Y-
style flow-through assembly.

The sensors are connected to the electro-
nics module.

The electronics module is wired in accor-
dance with the wiring diagram (circuit dia-
gram) and local regulations.

Ensure that all transport protection was 
removed.

Check all connections for leakage.

Sample water monitoring is active (chap-
ter 3.6.6).

1  Switch on power supply.
2  Perform initial configuration:

Select the language

Set the date and time

Enter the system name

Chlorine, chlorine dioxide, ozone or 
potassium permanganate measurement 
(DES sensors)

 

Check the limit values 1 and 2 (“Min" 
and “Max"), adjust if necessary.

Check the measurement range, adjust 
if necessary.

4  pH, OPR (Redox) and fluoride measure-

ment

Check the limit values 1 and 2 for pH/
ORP (Redox)/fluoride (Min and Max), 
adjust if necessary.

Check the measurement range for pH/
OPR (Redox)/fluoride, adjust if neces-
sary.

5  Configure mA outputs.
6  Carry out initial calibration of the sensors 

used.

 DANGER

Risk of injury or death!

The DEPOLOX® 400 M must not be operated
with flammable liquids. 

 ATTENTION

Risk of injury or damage to the device!

To ensure safe and correct commissio-
ning, knowledge of the operation, con-
nected electrical load, measurement 
signals, cable assignment and fuse pro-
tection of the connected devices and 
machines and the relevant safety regu-
lations is required.

Startup of the DEPOLOX® 400 M may 
therefore only be performed by quali-
fied and authorized electricians.

Incorrectly connected devices can be 
damaged, possibly irreparably, or cause 
faults in other equipment when they are 
switched on or in operation. 

Ensure that the measuring and control 
cables are not confused or make contact 
with one another. 

Never connect or disconnect any cables 
to which voltage is applied.

 WARNING

Risk of injury or damage to the device!

When connecting the DEPOLOX® 400 M 
to the power supply, a 6A back-up fuse 
must be used in the mains supply line.

Summary of Contents for DEPOLOX









































































































Reviews: