background image

Evolv DNA 75 

 

75 Watt Variable Power Module with Temperature Protection and USB 

The DNA 75 is a power regulated digital switch-mode DC-DC converter for personal vaporizers. It 

features Evolv’s patented Wattage Control, Temperature Protection, Preheat, OLED Screen, Reverse 
Polarity Protection, onboard programmable multicolor LED and waterproof onboard buttons. The USB 
port and Evolv’s EScribe software can be used to customize or monitor the user experience. The DNA 75 
runs from a single lithium polymer or lithium ion battery, and features battery monitoring and 
integrated 1A charger.  

Specifications 

 

Minimum 

Typical 

Max 

Output Power 

1 Watt 

 

75 Watts 

Output Voltage 

.2 Volt 

 

6.2 Volts 

Output Current, continuous 

 

 

30.0 Amps 

Output Current, instantaneous peak 

 

 

40.0 Amps 

Atomizer Resistance, temperature sensing wire, cold 

See Graph 

.15 Ohm 

See Graph 

Atomizer Resistance, Kanthal wire 

See Graph 

.25 Ohm 

See Graph 

Temperature Limit 

200

°

450

°

600

°

Input Voltage 

3.0 Volts 

3.7 Volts 

4.2 Volts 

Input Current 

.5 Amps 

12.0 Amps 

28.0 Amps 

Input Current, pulse 

 

 

32.0 Amps 

Screen On Current 

 

26mA 

 

Quiescent Current 

 

7mA 

 

Power Down Current 

 

0mA 

 

Efficiency 

 

85% 

 

Weight 

 

15g 

 

Footprint 

.71” x 2.60” 

 

18mm x 66mm 

Thickness 

 

.32” 

 

Screen size 

 

.91” OLED 

 

 

Summary of Contents for DNA 75















Reviews: