background image

13

www.evolutionpowertools.com

EN

WARNING: Mag Drills must not be connected to a power 
source until all assembly and preparation has been 
completed and a safety check carried out.  Evolution Mag 
Drills should only to be used on non-coated Mild Steel which 
is free from paint or loose rust etc. 

Remove the machine from the case and check that all accessories 
are present and correct. 

WARNING:

 All Magnetic Drilling machines are heavy. Enlist 

competent help when lifting these machines.

•    Place the machine onto a clean, sturdy work surface.
•  Attach the three handles into the spindle hub ensuring that they 

are fully seated. 

(Fig. 1)

•  Attach the Safety Guard and secure in place using the supplied 

fixing screws. 

(Fig. 2)

•  Attach the coolant/lubrication bottle to its service position. Use 

the tapped hole located at the top left of the machines casing 
and the Ø6 screw (provided). 

(Fig. 3)

•  Insert the ‘free’ end of the supply tube into the ‘quick connector’.

Note:

 

To release the delivery tube from the quick connector 

(Abb.3a)

 push the collar towards the brass union and withdraw 

the delivery tube.

Note:

 For some operations it may be convenient to remove the 

coolant/lubricant bottle and supply tube and use alternative 
methods of coolant or lubricant application.

TESTING - All Evolution Magnetic Drilling Machines

WARNING:

 

All Evolution Magnetic Drilling machines have Class 

1 insulation and must be earthed. Any power socket that this 
machine is connected to must be grounded to earth. Ensure 
that both operating switches are in the ‘OFF’ position before 
connecting the power cord to the socket.

WARNING: 

The power cord assembly is a custom terminated one. 

Replacement should only be carried out by a qualified technician. 
Use only replacement parts recommended by Evolution Power 
Tools. 

WARNING:

 

Do not perform any testing with a cutter or drill 

installed in the machine.
  
•  Place the machine onto a piece of clean 10 mm thick mild steel 

plate that is larger than the magnetic base of the machine.

•  Connect the plug into a mains supply outlet and switch on the 

socket (UK only).

•  Operate the rocker switch on the machines switch panel to 

energise the magnet. 

(Fig. 4)

ASSEMBLY AND PREPARATION

Fig. 1

Fig. 3

Fig. 2

Fig. 3a

Summary of Contents for S28MAG























Reviews: