Evolis KC200 User Manual Download Page 34

KC200 

KC200B

34

APPENDIX B

DECLARATIONS OF CONFORMITY KC200

In this section, you will find the certifications for your Evolis printer.

Declarations of Conformity

Concerning the Safety and Electromagnetic Compatibility of Radio Equipment 

(Directives RED 2014/53/EU, LVD 2014/35/EU, EMC 2014/30/EU)

Manufacturer name: Evolis

Manufacturer address: 

14, avenue de la Fontaine

 

Z.I. Angers Beaucouzé

 

49070 Beaucouzé, France

Equipment name: KC200

Year of manufacture: 

January 2019

I, the undersigned,
Mr. 

Serge Olivier

Declare under my own responsibility that the product described above is in con-

formity with the essential applicable requirements of the following directives: 

RED 2014/53/EU, LVD 2014/35/EU, EMC 2014/30/EU, and (RoHS2) 2011/65/EU:

Article 3.1 a: (electromagnetic compatibility protection requirement)

Safety standard applied 

EN60950-1: 2006 + A11 + A1 + A12 + A2 

 

EN50364: 2010

Article 3.1 b: (electromagnetic compatibility protection requirements)

EMC standard applied 

EN55032: 2012

 

EN55024: 2010

 

EN61000-3-2: 2014

 

EN61000-3-3: 2013

 

EN 301489-3: 2013 (V1.6.1.) 

 

Article 3.2: (proper use of the radio spectrum to avoid harmful interference)

EMC standard applied 

EN300 330-2 V1.6.1

Full name: Serge Olivier
Title: R&D Director
Date: January 7, 2019
Signature: 

EUROPE - Norway only: This product is designed for an IT power system with phase-to-phase 

voltage of 230 V. Earth grounding is via the polarized, 3-wire power cord.

FI: ”Laite on liitettävä suojamaadoitus koskettimilla varustettuun pistorasiaan”

SE: ”Apparaten skall anslutas till jordat uttag”

NO: "Apparatet må tilkoples jordet stikkontakt"

DK: "Apparatets stikprop skal tilsluttes en stikkontact med jord, som giver forbindelse til 

stikproppens jord".

FCC Federal Communications Commission notice

Radio frequency interference in the United States

   The KC200 model complies with the following specification:  

FCC Part 15, Subpart A, Section 15.107(a) and Section 15.109(a) 

Class B Digital device

Additional information:

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant 

to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful 

interference in a residential installation. This equipment generates, uses and can radiate radio frequency 

energy and, if not installed and used in accordance with the instructions, may cause harmful interference 

to radio communications. However, there is no guarantee that interference will not occur in a particular 

installation. If this equipment does cause harmful interference to radio or television reception, which can 

be determined by turning the equipment off and on, the user is encouraged to try the following measures:

- Reorient or relocate the receiving antenna.

- Move the equipment away from the radio or television. 

- Connect the equipment to a circuit other than that to which the receiver is connected.

- Consult the supplier or an experienced radio/TV technician.

Use of a shielded twisted pair cable is necessary to comply with the restrictions laid down by part 15 of the 

FCC Rules for Class B digital devices.

Pursuant to Part 15.21 of the FCC Rules, any changes or modifications made to this equipment without 

the express, written consent of the company Evolis may cause harmful interference and void the FCC 

authorization to operate this equipment.

We recommend keeping a distance of 20 cm between the user and the RFID module when it is in operation.

This device is compliant with the RSS of Industry Canada applicable to radio devices exempt from licensing. 

Its use is authorized under the following two conditions: (1) The device must not cause jamming and (2) the 

device user must accept any radio-electrical jamming it experiences, even if this compromises its operation.

 

Japanese radio frequency interference (VCCI)

   This equipment is Class B information technology equipment based on the rules laid down 

by the Voluntary Control Council For Interference by Information Technology Equipment 

(VCCI). Its use in or close to a residential area may cause radio interference. If this occurs, 

you must take appropriate steps.

Summary of Contents for KC200




































Reviews: