EVOC P12 Series Manual Download Page 27

Page: 27 / 131

Debugging

· 18 ·

P12 SERIES

LILED

(dual-color:

orange and green)

Network

speed

ACTLED

(single color:

green LED)

Network activity

Green 1000Mbps

Flash

Data being

transmitted

Orange 100Mbps

Off

No data being

transmitted

Off 10Mbps

Note: No matter the 1000Mbps LAN port has or has no Link signal, the ACTLED on the

left side means there is no data being transmitted. If there is data being transmitted, the

green LED on the left side should be at "Flashing" status. If the network is connected but

no data being received or transmitted, the green LED should be at "off" status; When there

is broadcast packet,it is normal if ACTLED is "Flashing".

5.2.5 HDMI Port

It provides one 19 Pin Type A HDMI port.

Pin

Signal Name

Pin

Signal Name

TMDS DATA2+

TMDS DATA2 Shield

TMDS DATA2-

TMDS DATA1+

TMDS DATA1 Shield

TMDS DATA1-

TMDS DATA0+

TMDS DATA0 Shield

TMDS DATA0-

TMDS CLK+

TMDS CLK Shield

TMDS CLK-

13 CEC 14

RSVD(NC

device)

15 SCL 16 SDA

17 DDC/CEC

Ground 18

+5V

HDMI1

Hot Plug Detect

Summary of Contents for P12 Series




































































































































Search results

Summary of Contents for P12 Series

Reviews:

Related manuals for P12 Series

Brands by name

Popular brands

EVOC P12 Series, Manual

Search results

Summary of Contents for P12 Series

Reviews:

Related manuals for P12 Series

Brands by name

Popular brands