Battery Installation
1.
Put two AAA batteries into the battery cassette observing correct polarities.
2.
Install the battery cover by sliding it horizontally in the direction of the arrow as shown
below:
Notes: Batteries must be correctly installed. Otherwise, damage might be caused to the
device.
Please put or remove batteries in right order, or is likely to damage the device bracket.
Please remove the batteries if the Oximeter will not be used for a long time.
Hang Lace Installation
1.
Thread thinner end of the hang lace through the hanging hole.
2.
Thread thicker end of the lace through the threaded end before pulling it tightly.
Maintenance and Storage
1.
Replace the batteries when low voltage lamp is lighted.
2.
Clean surface of the fingertip Oximeter before it is used in diagnosis for patients.
3.
Remove the batteries from the battery cassette if the Oximeter will not be operated for a
long time.
4.
It is best to store the product in a place where ambient temperatures are -20~55
°
C
(-4~131
°
F) and humidity is 10%-93%.
5.
It is recommended that the product should be kept in a dry environment. High humidity
might affect its lifetime or even damage the product.
6.
Please follow local ordinances regarding the disposal of used batteries.
Calibrating
1.
The functional tester cannot be used to assess the accuracy of the Oximeter.
2.
Index 2 that made by Bioteck company is a function tester. Set Tech to 1, R curve to 2,
then user can use this particular calibration curve to measure the Oximeter.
3.
The test methods used to establish the SpO2 accuracy is clinical testing. The Oximeter
used to measure the arterial hemoglobin oxygen saturation levels and these levels are
to be compared to the levels determined from arterial blood sampling with a
CO-Oximeter.
Declaration
EMC of this product comply with IEC60601-1-2 standard.
The materials which user can come into contact is no toxicity and no action on tissues, (I
don’t know what this means) comply with ISO10993-1,-5,-10.
Detailed descriptions of product functions
1. Display
Type:
OLED display
2. SpO
2
:
Measurement range: 70-99%
Accuracy: ±2% on the stage of 80%-99%; ±3% on the stage of 70%-80%;
3. Pulse
Rate:
Measure range: 30-235 BPM
Accuracy: ±2 BPM or ±2%
（
larger
）
Pulse Intensity: Bar graph Indicator
4. Power
Requirements:
Two AAA alkaline Batteries
Power consumption: Less than 40mA
Low power indication:
Battery Life:
Two AAA 1.5V, 600mAh alkaline batteries could continuously operate the Oximeter
for as long as 30 hours.
5. Dimension:
Length: 58mm
Width: 32mm
Height: 34mm
Weight: 50g (including two AAA batteries)
6. Environment
Requirements:
Operation Temperature: 5~40
°
C
Storage Temperature: -20~55
°
C
Humidity: 15%-80% in operation
10%-93% in storage
7. Declaration:
EMC of this product complies with IEC60601-1-2 standard.
8. Measurement Performance in Low Perfusion Condition:
required the test
equipment (BIO-TEK INDEX Pulse Oximeter tester) the pulse wave is available without
failure when the simulation pulse wave amplitude is at 0.6%.
9.
Interference Resistance Capacity against Ambient Light:
Device work normally
when mixed noise produced by BIO-TEK INDEX Pulse Oximeter tester.
Guidance and Manufacturer’s declaration – electromagnetic emissions-
for all EQUIPMENT and SYSTEMS
Guidance and Manufacturer’s declaration – electromagnetic emission
The
Pulse Oximeter
is intended for use in the electromagnetic environment specified below. The customer of
or the user of the
Pulse Oximeter
should assure that it is used in such an environment.
Emission test
Compliance
Electromagnetic environment – guidance
RF emissions
CISPR 11
Group 1
The
Pulse Oximeter
uses RF energy only for its
internal function. Therefore, its RF emissions are
very low and are not likely to cause any interference
in nearby electronic equipment.
RF emission
CISPR 11
Class B
The
Pulse Oximeter
is suitable for use in all
establishments, including domestic establishments
and those directly connected to the public
low-voltage power supply network that supplies
buildings used for domestic purposes.
Possible Problems and resolutions
Problems
Possible reason
Solution
SpO
2
or PR can not
be shown normally
1. Finger is not inserted correctly
2. Patient’s oxygen saturation value is
too low to be measured.
1..Retry by reinserting the finger
2. Try some more times. If you can make sure no
problems exist with the product, please go to a
hospital in a timely manner for exact diagnosis.
SpO2 or PR is erratic
1. Finger might not be inserted deep
enough.
2. Finger is trembling or patient’s body
is moving around.
1. Retry by reinserting the finger.
2. Try not to move around.
The Oximeter can
not be powered on
1. Batteries might be low or missing.
2. Batteries might be installed
incorrectly
3. The Oximeter might be damaged
1. Replace the batteries
2. Please reinstall the batteries.
3. Please contact a customer service center.
Indication lamps are
suddenly off
1. The product is automatically powered
off when no signal is detected for
longer than 8 seconds
2. Batteries might be low.
1. Normal
2. Replace the batteries
“Error3” or
“Error4” Displayed
on screen
1 .Low power
2. Receiving tube being shielded or
damaged together with broken
connector.
3. Mechanical Misplace for
receive-emission tube.
4. Amp circuit malfunction.
1. Replace the batteries
2. Please contact a customer service center
3. Please contact a customer service center
4. Please contact a customer service center
“Error7” displayed on
screen
1. Low power
2. Emission tube damaged.
3. Current control circuit malfunction.
1 Replace the batteries
2 Please contact a customer service center
3 Please contact a customer service center
Symbol Definitions
Symbol Definition Symbol Definition
The equipment type is BF
Heart rate (BPM)
Refer to user manual before
application
Low power indication
SpO
2
﹪
Hemoglobin saturation
SN
Serial No
Not for continuous monitoring
Date of manufacture
Distributor: EVO Medical Solutions
26378 289th Place
Adel, IA 50003
TEL:515.993.5001
FAX:515.993.4172
Toll free :800.759.3038
Web:
http://www.evomedical.com
Manufacturer:
Beijing Choice Electronic Technology Co., Ltd.
