Evikon PluraSens E2648-O3 User Manual Download Page 21 | Manualshive

Page: 21 / 21

background image

E2648-O3

Rev 22.06.2021

Warranty

This product is warranted to be free from defects in material and workmanship for a period
of one year from the date of the original sale. During this warranty period, the Manufacturer
will, at its option, either repair or replace a product that proves to be defective. This
warranty is void if the product has been operated in conditions outside ranges speciﬁed by
the Manufacturer or damaged by customer error or negligence or if there has been an
unauthorized modiﬁcation.

Manufacturer contacts

Evikon MCI OÜ

Teaduspargi 7/9, Tartu
50411 Estonia
[email protected]
www.evikon.eu

21

«
...
19
20
21

Summary of Contents for PluraSens E2648-O3






















Reviews:

No comments

Related manuals for PluraSens E2648-O3

Multi Gas Clip Simple Plus

Brand: Gas Clip Technologies Pages: 20

Brand: SAFERA Pages: 15

Brand: Abus Pages: 18

Toolsplit TSCE-500

Brand: Tecnosystemi Pages: 8

Brand: Channel Plus Pages: 4

Brand: Hali-Brite Pages: 21

Brand: Inter-m Pages: 18

Brand: Wolf-Guard Pages: 11

Brand: DMP Electronics Pages: 2

Brand: HIKVISION Pages: 12

Brand: Halo Smart Labs Pages: 34

Brand: Konig Security Pages: 56

Brand: Vitek Pages: 2

Brand: Bosean Electronic Technology Pages: 16

Brand: Avtech Pages: 7

PrecisionHD 720p

Brand: TANDBERG Pages: 29

Brand: Exotek Instruments Pages: 2

Brand: ADEMCO Pages: 72

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands