background image

E2658-C2H4 

Rev 12.03.2021 

 

18 

0x00D3 

211 / 

40212  RW 

Parameter tied to relay 
RE1 

0 –none 
2 – gas concentration 

9 – control by Modbus control, 
state set in MHR / 40214 

0x00D4 

212 / 

40213 

RW  Parameter tied to relay 

RE2 

0 – none 
2 – gas concentration 
9- – control by Modbus 

control, state set in MHR / 
40215 

0x00D5 

213 / 

40214 

RW  Forced state for relay 

RE1*** 

0 –off, 1 – on 

0x00D6  214/ 40215  RW  Forced state for relay 

RE2*** 

0 – off, 1 – on 

0x00D7 

215 / 

40216 

RW  Switching delay for relay 

RE1 

0...1000 (s) 

0x00D8 

216 / 

40217 

RW  Switching delay for relay 

RE2 

0...1000 (s) 

0x00D9 

217 / 

40218 

RW  Minimal on/off time for 

relay RE1 

0...1000 (s) 

0x00DA 

218 / 

40219 

RW  Minimal on/off time for 

relay RE2 

0...1000 (s) 

Address  Reg / MHR  RW  Description 

Supported values (dec) 

Default 

0x00DB 

219 / 

40220  RW  Control logic for relay RE1 

0 – none  

1 – relay on at high values  
2 – relay on at low values  
3 – relay on at values 
within the range  
4 – relay on for the values 

out of the range 

0x00DC 

220 / 

40221 

RW  Control logic for relay RE2 

0 – none 
1 – relay on at high values  
2 – relay on at low values  
3 – relay on at values 

within the range  
4 – relay on for the values 
out of the range 

Summary of Contents for E2658-C2H4-230






















Reviews: