evertz CP-1024E User Manual Download Page 21 | Manualshive

Page: 21 / 28

background image

CP-1024E

Control Panel

5. SYSTEM

CONFIGURATION

5.1.

UPGRADING THE CP-1024E PANEL

5.1.1. System

Requirements

1. The user must have a laptop or PC connected to the same network as the CP-1024E.

2. In order to run the EQX server, you must have one of the following browsers installed on your

machine: Firefox, Chrome or Safari

5.1.2. Identifying the IP Address

The IP Address can be identified using the procedure outlined below or by referring to section 4.3.1.1.

1. To identify the IP address, hold down the top and bottom left rotary encoders (TL and BL) for

approximately 6 seconds.

2. When the main engineering menu appears, toggle to the

SETUP

menu and push in the

Menu

rotary encoder.

3. Next, select the

IP Addr

option and push in the

Menu

rotary encoder once again. Obtain the IP

address, which will appear on the third display screen.

4. At this time, ensure that one of the above mentioned browsers from section 5.1.1 is installed on

your machine.

"

Please note that the CP-1024E and the PC must be on the same network.

Revision 1.1

Page 13

«
...
19
20
21
22
23
...
»

Summary of Contents for CP-1024E





























Reviews:

No comments

Related manuals for CP-1024E

Brand: Samson Pages: 92

Brand: Jafar Pages: 10

Brand: Panasonic Pages: 72

Brand: Panasonic Pages: 45

Brand: Panasonic Pages: 24

Brand: Bang & Olufsen Pages: 36

Brand: Mad Catz Pages: 4

Brand: Harman Kardon Pages: 25

Brand: Uniss Pages: 21

Brand: NAPCO Pages: 48

Magnum Alert 2600

Brand: NAPCO Pages: 68

Brand: Maximum Controls Pages: 58

Brand: Reer Pages: 2

Brand: Dickey-John Pages: 109

by-me Eikon 20526

Brand: Vimar Pages: 6

Brand: SAGEMCOM Pages: 2

Brand: Instant Care Pages: 2

Soluna Remote Control

Brand: Rollei Pages: 8

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands