evertz 7780ASIB2-DS3/E3 Manual Download Page 15 | Manualshive

Page: 15 / 36

background image

7700 MultiFrame Manual

7780ASIB2-DS3/E3 2 Channel ASI + Ethernet DS3/E3 Transceiver

Revision

2.0

Page - 11

4.2.1. Control

Menu

The

Control

menu enables the user to control and set different parameters on 7780ASIB2-DS3/E3 cards.

4.2.1.1.

Passcode Protection Configuration

The channels’ passcode protection can be controlled using menu selections. To configure the channel
passcode protection from the

CTRL

menu, use the toggle switch/pushbutton to select the

PSWD

menu item.

Use the toggle switch to increase or decrease the digits one at a time and use the pushbutton to select
each digit until the correct passcode is entered (Default

7154

).

Once the correct passcode is entered, the user has the option of blocking individual input or output
channels, along with limiting input bandwidth of a particular channel. If the correct passcode is not
entered, the user may view the current configuration of these passcode protected menu items, but may
not make changes.

The passcode may be changed from the

CTRL

menu. To change the passcode, use the toggle

switch/pushbutton to select the

PSWD

menu item and then choose the

PSWL

menu item. A new passcode

may then be selected and stored.

CTRL

PSWD

PSWL

0 to 9999

The following selections are available:

PSWL

Store a new passcode (0-9999)

This menu is not available without first entering the correct passcode.

For Ethernet transport, the user may select between two modes of operation, Manual and Auto. In Manual
mode, the user defines the bandwidth allocated for Ethernet transport. In Auto mode, the allocated
bandwidth for Ethernet transport is the Total System Bandwidth minus the bandwidth used for ASI video
transport. To configure

Ethernet Mode

from the

CTRL

menu, use the toggle switch/pushbutton to select

the

PSWD

menu item and then choose the

ETH

menu item.

CTRL

PSWD

ETH

MODE

MAN (0-25)
AUTO

The following selections are available:

MAN

Enable Manual mode. User selectable from 0-25Mbps

AUTO

Enable Automatic mode

To configure

Input Channel Blocking

from the

CTRL

menu, use the toggle switch/pushbutton to select the

PSWD

menu item and then choose the

IN1

or

IN2

menu item, followed by the

OUTP

menu item.

CTRL

PSWD

IN1 / IN2

OUTP

EN, DIS

The following selections are available:

EN

Enable Input Channel

DIS

Disable Input Channel

When Disabled, the data input on the selected signal is not placed on the
DS3/E3 link data stream.

«
...
13
14
15
16
17
...
»

Summary of Contents for 7780ASIB2-DS3/E3





































Reviews:

No comments

Related manuals for 7780ASIB2-DS3/E3

Brand: FAAC Pages: 2

Brand: WDS Pages: 32

XM2GO - MyFi Portable Satellite Radio

Brand: XM Satellite Radio Pages: 15

Brand: Icom Pages: 48

Dpharp vigilantplant EJA Series

Brand: YOKOGAWA Pages: 31

Brand: PCTV Systems Pages: 2

Brand: Hallicrafters Pages: 19

Brand: Walter Dittel Pages: 33

Brand: Future light Pages: 31

Rollixo Smart io

Brand: SOMFY Pages: 92

Brand: Green image Pages: 3

Brand: Botech Pages: 48

2.4 GHZ WIRELESS VIDEO SENDER WITH IR EXTENDER

Brand: Strategic Victa Pages: 17

Brand: DX Engineering Pages: 36

Brand: Extron electronics Pages: 37

Brand: ZENDit Pages: 16

Brand: Vaisala Pages: 13

Brand: CIRCUIT DESIGN Pages: 12

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands