background image

7700 MultiFrame Manual 

7700ADA7-EQ Equalizing Analog Video Distribution Amplifier

 

Revision 1.2

 

REVISION HISTORY 

 

 

REVISION DESCRIPTION DATE

 

 
1.0 

Original Version 

Jul 05 

 
1.1 

Updated block diagram 

Oct 07 

 
1.2 

General format clean up 

Sept 09 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

Information contained in this manual is believed to be accurate and reliable. However, Evertz assumes no responsibility for the use thereof nor for 
the rights of third parties, which may be affected in any way by the use thereof.  Any representations in this document concerning performance of 
Evertz products are for informational use only and are not warranties of future performance, either expressed or implied. The only warranty offered 
by Evertz in relation to this product is the Evertz standard limited warranty, stated in the sales contract or order confirmation form. 
 
Although every attempt has been made to accurately describe the features, installation and operation of this product in this manual, no warranty is 
granted nor liability assumed in relation to any errors or omissions unless specifically undertaken in the Evertz sales contract or order confirmation.  
Information contained in this manual is periodically updated and changes will be incorporated into subsequent editions.  If you encounter an error, 
please notify Evertz Customer Service department. Evertz reserves the right, without notice or liability, to make changes in equipment design or 
specifications. 

 

Summary of Contents for 7700ADA7-EQ MultiFrame













Reviews: