evertz 5782DEC User Manual Download

Page: 46 / 60

5782DEC

Professional H.264 and MPEG-2 Decoder

Page - 36

Revision 1.0

WEBEASY

Video PID:

This parameter displays the Video Packet ID (PID). The video PID allows the decoder to

sort the video packets in the transport stream to organize them for output in kbps.

Video Bitrate:

This parameter displays the video bitrate of the associated video stream.

Video Compression Type:

This parameter displays the video compression type of the associated

video stream.

Video Chroma Format:

This parameter displays the chroma format of the associated video stream.

Video Resolution:

This parameter displays the video resolution of the associated video stream.

Video Frame Rate:

This parameter displays the video frame rate of the associated video stream.

Continuity Counter Error

Video Count:

This parameter returns the current value of the video CC error count.

Video Reset Count:

This parameter allows the user to reset the count of video continuity errors.

Video Threshold:

This parameter allows the user to set the video CC error threshold for the video

CC error traps.

Audio Continuity Counter Error

Audio Count:

This parameter displays the number of audio continuity errors counted.

Audio Reset Count:

This parameter allows the user to reset the count of audio continuity errors.

Audio Threshold:

This parameter displays the error threshold for audio continuity.

5.5.

DECODER AUDIO MONITOR

Figure 5-8: WebEASY

– Decoder Audio Monitor Tab

Summary of Contents for 5782DEC





























































Search results

Summary of Contents for 5782DEC

Reviews:

Related manuals for 5782DEC

Brands by name

Popular brands

evertz 5782DEC, User Manual

Search results

Summary of Contents for 5782DEC

Reviews:

Related manuals for 5782DEC

Brands by name

Popular brands