evertz 570NAT-HW-X19 User Manual Download

Page: 37 / 56

570NAT-HW-X19

High Density Network Address Translator

Revision 1.0

Page - 27

4.5.1. LAN to WAN: Input Flow Configuration

Flows 1 to 256

Mode:

This control allows the user to enable or disable the input associated with that flow.

Input Destination IP Address:

This control allows the user to set the Input Destination IP address of

the packets to be received.

Input Destination UDP Port:

This control allows the user to set the Destination UDP Port number to

be received.

VLAN:

This control allows the user to assign this flow to a VLAN.

SSM Filter:

This control allows the user to enable Source Specific Multicast (SSM) channel based

filtering.

Input Source IP Address:

This control is used in NAT mode to configure the output header with the

desired source IP address.

Input Bitrate:

This monitor will display the bit rate of the streams that are being received in kbps.

Input Bitrate Cap:

This control allows the user to set a cap on the bitrate for each flow in Kbps.

4.5.2. LAN to WAN: Address Translation Configuration

Flows 1 to 256

Output Mode:

This control is used to set the output mode on the flow stream. Options are

Pass

Through

Modify.

Pass Through

will enable the stream to pass through without making any changes

to the headers while

Modify

enables changes to the headers.

Source IP Address:

This control is used in NAT mode to configure the output header with the desired

source IP address.

Source UDP Port:

This control is used in NAT mode to configure the output header with the desired

source UDP Port.

Destination IP Address:

This control is used in NAT mode to configure the output header with the

desired destination IP address.

WAN Interface:

This control allows the user to set the WAN interface this flow passed through in LAN

to WAN, the options given are to flow directly through data port or through a NAT virtual interface

(Interfaces 1-15, Figure 4-10 shows an abbreviated menu).

Destination MAC for Unicast IP:

This field displays the destination MAC.

Destination UDP Port:

This control is used to enter the destination UDP port.

Summary of Contents for 570NAT-HW-X19

























































Search results

Summary of Contents for 570NAT-HW-X19

Reviews:

Related manuals for 570NAT-HW-X19

Brands by name

Popular brands

evertz 570NAT-HW-X19, User Manual

Search results

Summary of Contents for 570NAT-HW-X19

Reviews:

Related manuals for 570NAT-HW-X19

Brands by name

Popular brands