INSTALLATION INSTRUCTIONS
1. Open Carton and Inspect Parts.
Installation
Parts included – refer installation diagram
Item No.
QL2 Filter Head with Mounting Bracket
1
Everpure SPA-400 Filter Cartridge
2
Mounting Screws
3
Cistern Tap with Dual Check Valve
4
Pex Hose 550mm – 1/2” female to 3/8” male
5
Brass Hex Nipple 3/8” male to 1/2” male
6
Horizontal Stabilizing Bracket
7
Filter Monitor Alarm
8
Plumbing Tape
9
2. Ensure that the cold water at mains supply is
turned off
Where an existing tap and connections are already
installed - after you have turned off the mains cold
water at the mini cistern tap, open the kitchen /
mixer tap and release any water pressure.
Unscrew the braided flex hose from the existing
cold water line mini cistern tap or isolation valve.
Clean the 1/2” male water connection thread.
3. Undersink Mounting Position
As you will note from the associated diagram, the
Everpure SPA-400 Filter System can be installed in
either the horizontal or vertical position.
a)
Vertical Installation
Measure 51 cm from the base of the cabinet (or
shelf), and mark the mounting location for the
top of the filter head. Make sure that there is
adequate space to avoid crimping the water line
flex hoses. Also make sure your chosen location
offers easy access for future cartridge changes.
b)
Horizontal Position
Measure 51 cm horizontally,
and mark the mounting location for the side
of the filter head and end of the filter cartridge.
Make sure that there is adequate space to avoid
crimping the water line flex hoses. Also make
sure your chosen location offers easy access for
future cartridge changes and installation of the
stabilizing support bracket. (item 7).
4. Important - Changing the inlet and outlet on the
filter head. You will notice that at the top of the
Head Assembly (item 1) there is an arrow that
indicates the direction of flow into and out of
the filter head. In some instances, to ensure an
easier installation, it may be appropriate to have
the inlet side on the right of the head assembly
as opposed to the left hand side which is
provided as standard. This can be easily done
by removing the four (4) screws on the top of
the head assembly, turn the head around the
opposite way and replace the screws ensuring
a tight fit. This allows flexibility when choosing
your desired install location.
a) Apply plumbing tape (item 9) to the Pex Hose
3/8” male connection (item 5). Wrap tape in
direction of the thread to ensure a tight fit and
avoid leaks. Screw this connection to the inlet
side of the filter head. You will notice an arrow
on the top of the filter head (item 1) which
shows direction of water flow.
b) Apply plumbing tape to the Brass Hex Nipple
(item 6) both sides. Wrap tape in direction of
the thread to ensure a tight fit and avoid leaks.
Screw this connection to the outlet side of the
filter head (item1).
c) Securely mount the Filter Head Assembly (item
1) on the cabinet wall using two of the mounting
screws (item 3) provided. The filter head will
be installed vertically or horizontally depending
upon your desired location.
5. Connect Cistern Tap with Dual Check Valve –
(item 4) IMPORTANT – It is a legal requirement
under Australian Plumbing Standards that the
Dual Check Valve be installed. If this part is not
installed all warranties are null and void.
a) Apply plumbing tape (item 9) to the 1/2” male
connection on the outlet of the cistern tap with
dual check valve (item 4). Wrap tape in direction
of the threads to ensure a tight fit and avoid
leaks.
6. Attach Flex Hose (item 5)
Connect the 1/2” female end of the Pex Hose
(item 5) - to the 1/2” male end.
7. Attach Filtered Water to Cold Water Line of
Kitchen Tap
Take the braided flex hose that is attached to the
kitchen tap. Having applied plumbers tape to the
1/2” male hex nipple (item 6) – screw the 1/2”
female end of the braided flex hose onto the nipple
(outlet side of filter head).
8. For Horizontal Installations – Install Support
Bracket (item 7)
Where the system is installed horizontally the unit
requires support at the base of the filter cartridge
with the Stabilizing Bracket (item 7). Locate the
bracket (item 7) in a position that allows three
important functions;
a) Firstly, the bracket needs to be located so that
the filter cartridge can be removed when it is
replaced. Suggested location is at the base of
the filter cartridge.
b) The bracket must be level with the filter head –
so that the filter cartridge sits in a level horizontal
position.
c) Finally, the bracket needs to be screwed into
the cabinet using the two remaining mounting
screws (item 3) and set in a manner whereby
the bottom of the bracket supports the water
filled filter cartridge horizontally.
9. Install Filter Cartridge (item 2)
a) Hold filter head (item 1) firmly with one hand.
b) Align cartridge lug with label on filter head.
c) Insert filter cartridge (item 2) and push into filter
head assembly (item 1).
d) Turn it to the right (about 1/4 turn) until it stops.
10. Flush the Filter Cartridge
a) Turn mains water supply back on at mini
cistern tap.
b) At this stage check for leaks and fix if
necessary
c) Turn kitchen tap on and flush the filter cartridge
for at least 2 minutes. Collect water in
container and use for garden etc.
NOTE – Flushing the filter cartridge is important
to remove air from the system and any loose
carbon. At first the water may appear cloudy due
to compressed trapped air in the filter and hoses.
However the cloudiness will disappear over time
and with use.
11. Installing the Filter Monitor Alarm (item 8
)
The filter monitor alarm (item 8) is supplied to
assist you with knowing when it is time to replace
your filter cartridge. Regular annual cartridge
replacement ensures that your filter system is
maintained in accordance with the manufacturers
recommendations.
a) Remove double sided tape and plastic
wrapper from monitor.
b) On the back of the monitor - pull the tab back.
c The LED and buzzer will cycle 3 times to
confirm the start.
d) It is programmed to flash and sound again in
11 months.
e) Remove the two adhesive tapes from the
back of the monitor and locate/mount in a
convenient location under your kitchen sink.
NOTES
1) This installation must comply with all
applicable state and local regulations.
2) Do not use with water that is microbiologically
unsafe or of an unknown quality without
disinfection before or after the system.
3) When storing filtered water in a refrigerator
please ensure the container has an air tight
seal / lid.
WFA and Everpure Inc. warrants to you, the first person
who has purchased and used the unit (“you”) that
this unit is free from defects due to faulty material and
workmanship in accordance with the conditions set out
in this document.This warranty is provided to you in
addition to your rights at law,including but not limited to
your rights under the Trade Practices Act 1074 (Cth) and
applicable legislation in your Australian State or Territory.
What this warranty covers:
This warranty covers defects due to faulty material and
workmanship of the unit supplied to you:
• For a period of 5 years from the date of purchase in
respect of the entire unit, excluding the Replaceable
Elements.The Replaceable Elements are consumable
components and all parts of the unit which can be
replaced including but not limited to the filter or water
treatment cartridge if there is a defect in the filter or
cartridge.This does not include the replacement of
the filter or cartridge to extend the life of the filter or
cartridge. The life of the filter cartridge is affected by
water quality, usage and water pressure.The warranty
only extends to the original purchaser of the unit.
What this warranty does not cover:
This warranty does not cover the unit or a Replaceable
Element of the unit where:
• The defect, fault or failure is attributable, or
substantially attributable to misuse, abuse, accident,
misapplication, neglect, freezing, oxidizing agents
(including but not limited to chlorine, ozone,
chloramines and other related components) or act of
God;
• The unit has been in conditions which do not conform
to the recommended design guidelines or has been
operated in a manner which is contrary to WFA’s
printed instructions;
PRODUCT
SPECIFICATION
• Usage: For cold water only.
• Temperature Range: 2-38
o
C
• Min.-Max. Working
Pressure:10-125 psi
(0.7-8.6 bar)
• Service Flow Rate:
8.3 Litres per minute
• Capacity:11,355 litres
• Micron Rating: Half
(0.5) micron
• Removes/Reduces:
Chlorine,cysts,lead,
giardia,cryptosporidium,
bad taste and odours, and
all particles down to half
micron in size
• This filter does not remove
fluoride
• Filter Change: Annually or
sooner if flow rate becomes
inconveniently slow.
• The unit has not been installed in accordance with
WFA’s printed instructions and has not been installed
in compliance with all applicable laws, regulations and
industry standards;
• The unit has not been used in accordance with the
manufacturer’s instructions;
• The unit does not meet the conditions for use
described in the owners manual or performance data
sheet for this unit
• You use accessories or components which do not
meet WFA’s specifications as set out in the Owners
Manual;
• The defect,fault or failure is due to normal wear and
tear;
• The defect, fault or failure has occurred where the
unit has been used reasonably or has reached its
serviceable life;
• The serial or model number label of the unit is
removed or defaced;
• The unit is serviced, modified, altered or repaired
by an unauthorized or unqualified person;
How to make a claim under this warranty:
To make a claim under this warranty you must contact
WFA within 21days of the defect, fault or failure
occurring. WFA Warranty Contact number is
1300 785 355. At the time of repair or replacement
under your warranty claim you must provide to WFA:
• Proof that you purchased the unit from an authorized
retailer or dealer within the warranty time; and
• A copy of a certificate which certifies that the unit was
installed in compliance with our printed installation
instructions and all applicable laws, regulations and
industry standards.WFA will only pay for repair or
replacement upon receipt of proof of your purchase
showing the date of purchase.
Limitation of Liability of WFA under this warranty:
Where a warranty exists or is implied by law, WFA’s
liability is limited (to the extent that it can be limited)
to repair or replacement of the faulty Replaceable
Element or the unit or an equivalent unit. WFA may, in its
discretion, choose whether it shall repair or replace any
unit or Replaceable Element or WFA may choose to pay
to you the cost of replacing the Replaceable Element
or the unit or the cost of having the unit repaired. To
the extent permitted by law, WFA assumes no liability
whatsoever and disclaims all liability for direct, indirect or
consequential loss, or special, general or other damage
or expense caused by or arising out of:
• Any failure to install or use the unit in accordance with
the Manufacturers Instructions, the Installation and
Operating manual or WFA’s printed instructions; or
• The purpose for which you are purchasing the unit.
You acknowledge that the quality of water supplied and
your water usage rate and influent water pressure may
vary seasonally or over a period of time.
In addition to this water characteristics can differ if the
unit is relocated or the environment changes.
You acknowledge that WFA does not know your
requirements and cannot and does not warrant that the
unit is fit for the purpose for which you intend to use
the unit or is appropriate for the purpose for which you
intend to use the unit. WFA does not authorize others to
assume any obligation on its behalf even if you inform
them of the purpose for which you intend to use this
unit.
WARNING
WFA does not recommend making
alterations to your existing plumbing to accommodate
this filter system. If you wish to modify existing plumbing
you must comply with AS 3500 and use a licensed
plumber. Where internal water pressure exceeds 1000
kPa a Watermark approved Pressure Limiting Valve must
be installed prior to the filter system.
WARNING
The contaminants or other substances
removed or reduced by this water treatment system are
not necessarily in your water supply. Do not use with
water that is microbiologically unsafe or of an unknown
quality without disinfection before or after the system.
IMPORTANT
This filter is designed to be used with
mains/city water supplies. If the incoming water is from
a water tank or bore, install a suitable prefilter prior to
this filter system to prolong filter cartridge life.
CAUTION
Safely isolate the water supply prior to
installing the filter system to avoid injury and property
damage.
IMPORTANT NOTICE
The Everpure SPA-400
system filters water down to half a micron. The filter’s
very fine mechanical and chemical filtering process
removes chlorine, dirt, cysts and many other potential
contaminants. When water is filtered so finely it can
absorb part of everything it comes into contact with.
This can cause taste and odour issues.
Accordingly, you may find that with new kitchen tapware
the braided flex hose supplied with the new kitchen
tap has a rubber internal. This rubber internal may, in
some instances, cause taste and odour issues when the
filtered water first comes into contact with the hose.
Should this occur then flush the filtered water through
the hose over a period of time to remove taste and
odour issues.
If this does not solve the issue please contact the WFA
Customer Service Centre on 1300 785 355. WFA’s
distributors have available to purchase, a replacement
hose, with a special food grade internal, to resolve the
taste or odour issue.
Product Specifications:
The unit must only be used for a portable
water source and with cold water (with a temperature range
between 2 and 38o C).
Owners Manual
SPA-400
TOOLS REQUIRED
FOR INSTALLATION
• Philips Head Screwdriver
• Adjustable Wrench
• Tape Measure
• Pencil
WARRANTY
1. QL2 Filter Head with Mounting Bracket
2. Everpure SPA-400 Filter Cartridge
3. Mounting Screws
4. Cistern Tap with Dual Check Valve
5. Pex Hose 550mm – 1/2” female to 3/8” male
6. Brass Hex Nipple 3/8” male to 1/2” male
7. Horizontal Stabilizing Bracket
8. Filter Monitor Alarm
9. Plumbing Tape
