EverFocus ES0812-31 User Manual Download Page 48

Page: 48 / 56

PoE Switch

Figure 9-2



Member:

This column allows you to select the member Ports.



Status:

This column allows you to Enable/Disable the Trunk Group.



Type:

This column allows you to choose

Static

Trunking or Dynamic

LACP

Trunking.

After Select the

LACP

Trunk type, the following parameters can be configured. Please

noted that the parameters of the both ends of the LACP should be the same.



Operation Key:

This column allows you to type operation key.



Time Out:

This column allows you to select

Long Time Out

Time or

Short Time

Out

Time. The Long Time Out is around 30 seconds, the Short Time Out is around

3 seconds, however, the link partner of other supplier may not use the same
value. The longer time then will be used.



Activity:

This column allows you to select

Passive

Active

mode.

Note: If you enable LACP on some specified ports and their link partners are normal
port without LACP, these specified ports cannot transmit packet to/receive packet
from the link partner.

Summary of Contents for ES0812-31

























































Search results

Summary of Contents for ES0812-31

Reviews:

Related manuals for ES0812-31

Brands by name

Popular brands

EverFocus ES0812-31, User Manual

Search results

Summary of Contents for ES0812-31

Reviews:

Related manuals for ES0812-31

Brands by name

Popular brands