manualshive.com logo in svg

Everflo EDS120, Installation Manual, Page: 3 / 38

Share
Download
Everflo EDS120 Installation Manual Download Page 3

02

EVERFLO STAINLESS uV

uNVENTEd HOT WATER CyLINdERS

STORAGE PRIOR TO INSTALLATION
EVERFLO STAINLESS uV should be stored in its original packaging 
in an upright position in an area free from excessive damp.
Regulations G3+L.

HANdLING PROduCT
The EVERFLO STAINLESS uV  should be carried upright where 
possible. Assessments of risks for carrying the cylinder should 
be conducted. use more than 1 person for carrying where 
appropriate. Always follow latest guide lines for lifting techniques, 
to avoid injury and damage to the product.

WATER SuPPLy
EVERFLO STAINLESS uV  operates at 3 bar (controlled by the inlet 
control set) and is capable of delivering over 50 litres per minute. 
The high quality inlet control set has been designed to make the 
most of the flow rates available, however the performance of any 
unvented system is only as good as the mains water supply. The 
maximum possible water demand should be assessed, taking 
into consideration that both hot and cold services are supplied 
simultaneously from the mains.
The water supply should be checked to ensure it can meet these 
requirements. If necessary, consult the local water company 
regarding the likely pressure and flow rate availability.
If measuring the water pressure, note that a high static (no flow) 
mains pressure is no guarantee of good flow availability. In a 
domestic installation 1.5 bar and 25 l/min. should be regarded as 
the minimum. The maximum mains pressure that the inlet control 
set can accept is 12 bar.
Consideration should be given to upgrading existing ½” (15mm) 
cold mains pipework to a larger size if the recommended 
minimum pressure/flow rate is not being achieved.

ELECTRIC SuPPLy
The EVERFLO STAINLESS uV  requires 240 Volt electrical supply for 
the standard Incoloy immersion elements. The electrical supply 
to each immersion heater must be fused at 13A via a double 
pole isolating switch to BS 3456. The cable must be at least 
2.5mm2 heat resistant (85°C HOFR) sheathed flex complying to BS 
6141:1981 Table 8. 

uNPACKING THE uNIT
EVERFLO STAINLESS uV comes complete with the fittings required 
to complete the installation. Please see over for component 
content list.

High flow rate inlet control set
TS201-533

Temperature and pressure relief valve
TS202

Acetal tundish 15 x 22 mm
TS3

Incoloy long life  
3 kW immersion heater
TS9 - dIRECT     TS10 - INdIRECT

Two port valve
TS5

dual thermostat
uS201

High Limit thermostat
TS28

Installation &
Maintenance Instructions

Expansion Vessel

• 60, 90, 120 & 150 ltr units - 12 ltr vessel TS212
• 180, 210 & 250 ltr units - 18 ltr vessel TS219
• 300 ltr units - 25 ltr vessel 

 

TS224

Summary of Contents for EDS120







































Reviews:

No comments