background image

Charging functions: constant current, constant voltage, current limiting, voltage limiting and 
cycling. 
The accuracy for constant current: the accuracy for constant current is less than 

±

1% when 

the rated value ranges from 20% to 100% 
The accuracy for constant voltage: the accuracy for constant voltage is less than 

±

1% when 

the rated value ranges from 20% to 100%. 
The running mode for the main circuit: Three- phase full-bridge controlled rectifier. 
Communication  interface  and  protocol:  RS

232

 interface  (support  standard  MODBUS-

RTU protocol)  
Ambient temperature: range from 0

 to 40

 

Ambient humidity: not higher than 90% 
Altitude: less than 2KM. 

2.3. Performance parameters 

Control mode: 

The  charge-discharge  process  of  all  kinds  of  batteries  could  be  set  and  the  parameters  are 
automatically controlled, which could reserve the charge formula. 

Running mode:   

Constant  current  charging,  constant  voltage  and  limiting  current  charging,  constant  current 
and limiting voltage discharging, cycling, etc. 

Protection:   

Reserving  data  when  there  is  over-current,  over-voltage,  current-cutting  and  power  off.  It 
could automatically recover when power on and provide phase break protection.   

Phase transformation: 

Setting time, voltage, current etc. 

Record:   

Recording the charging data, voltage-current curve, wrong information and operation record. 

Rectifying mode:   

Three- phase full-bridge controlled rectifier 

Cooling mode:   

Self cooling or air cooling 
The accuracy for stable current and voltage: the accuracy for stable current and voltage is less 
than 

±

0.5% 

The accuracy for time: 

30S/24h 

Operating mode instructions: 

Constant  current  charging:  setting  charging  current.  Transition  has  two  modes:  time  and 
voltage 
Constant  voltage  and  limiting  current  charging:  setting  controlled  current  value  and 
controlled voltage value. Transition has two modes: time and current 
Cycling: setting the charging steps from one to five. Inside could loop and nest. 

Note: 

please  find  the  specific  setting  modes  in  the  chapter  of  touch  panel  operating 

instruction. 

Summary of Contents for uXcel Series



























Reviews: