background image

37

36

TOC

Forward-facing Installation with 
Lower Anchor Connectors

LATCH is a system for attaching the child restraint to your 

vehicle seat. It is to be used in place of your vehicle’s seat 

belts, and can be used in vehicles with LATCH anchors. Your 

vehicle owner’s manual may refer to this system as ISOFIX 

or Universal Anchorage System (UAS).

• 

ONLY

 use for securing child restraint to lower anchor 

bars.

• 

ALWAYS

 read and follow exactly the instructions which 

accompany your vehicle and child restraint.

• 

NEVER

 attach two hooks to one vehicle lower anchor 

bar.

• 

DO NOT

 use the vehicle seat belts to install a child 

restraint when using the Lower Anchor Connector 

Assembly.

•  This Lower Anchor Connector Assembly is intended to 

be used 

ONLY

 as described in these instructions. Serious 

injury or death may result from misuse.

• 

ALWAYS

 be sure that the Lower Anchor Connector hook 

is fully engaged onto the Vehicle Lower Anchor Bar by 

pulling hard on the Lower Anchor Connector strap. If 

it is not totally engaged, the Lower Anchor Connector 

Assembly will not secure your child restraint. Serious 

injury or death may result.

•  To avoid a strangulation hazard, you 

MUST

 store the 

unused Lower Anchor Connector Assembly, with all slack 

removed, in storage area on the base (page 45). Roll 

or fold excess lower anchor connector strap and secure 

with a rubber band to prevent serious injury to vehicle 

occupants.

SecureRight™

Quick Connector™

Remove two lower anchor connector hooks 

A

, or clips 

B

, from the the base 

C

.

1

A

C

2

Remove the seat pad from the seat shell (page 47).

Loosen harness straps 

D

 (page 44) and place them 

out of the way, as shown. 

• If your lower anchor connector strap 

E

 is already  

in the forward- facing position (back openings), 

proceed to step 6.

• If your lower anchor connector strap 

E

 is in the rear-

facing position (front openings), continue to step 3.

C

B

Lower Anchor Connector 

Strap in Forward-facing 

Position

Lower Anchor Connector 

Strap in Rear-facing Position

D

D

E

E

Hook

Adjuster

Strap

SecureRight™

Quick Connector™

Clip

Strap

Adjuster

Know Your Lower Anchor 

Connector Assembly

The lower anchor connector assembly that comes with your 

child restraint will be one of the two types below.

•  In addition to these instructions, read and follow your 

vehicle owner’s manual regarding installation of child 

restraints and LATCH. If there is a discrepancy, follow 

your vehicle owner’s manual.

DO NOT

 Install by this 

method for a child weighing 

more than 22.7 kg (50 lb.).

For

ward-facing

WARNING

WARNING

Summary of Contents for 38211712
































Reviews: