manualshive.com logo in svg

EVAPCO eco-Air Series, User Manual

Share
Download
EVAPCO eco-Air Series User Manual Download Page 24

  

24  

Controller User Manual

 

 

 

The Fan Speed/Temperature Screen shown in Figure 31 determines the various speeds at which the eco-Air unit runs in various modes.  

Note that the fan speeds are set in percentage of the fan motor’s nameplate speed.  The energy saving speed is not active unless the 
eco-Air unit is equipped with a precooling system.  The energy saving fan speed allows the precooling system to activate one the fan 
speed reaches the energy saving value.  Once the precooling system is activated, the fan motors will continue to increase in speed if 
the active setpoint is not met.  The speed will continue to increase until the maximum allowed fan speed is met.  To disable the energy 
saving functionality, set the energy saving fan speed to the maximum allowed fan speed. 

 

The quiet operation fan speed limits the speed of the fan motors whenever the Quiet Mode is activated.  Quite Mode may be activated 

via the scheduler or a digital input.  If the quiet mode fan speed is less than the energy saving fan speed, the precooling system will 
be prevented from operating.  See Figure 7 for setup information.  

 
When cooling is not required and the fan speed settles to the minimum allowed fan speed, the fans will turn off based on the shutoff 

timer and offset. 

 

 

Fan speed and temperature setpoints 

 

Parameter

 

 

Description

 

 

Default

 

 

Max. Allowed

 

 

The maximum speed that the fan motors will reach when 
Quiet Mode is not active.

 

 

100%

 

 

Quiet Operation

 

 

The maximum fan motor speed allowed when Quiet Mode 
is activated via the scheduler or digital input.

 

 

100%

 

 

Energy Saving

 

 

The fan speed at which the pre-cooling system will 
activate.

 

 

100%

 

 

Min. Allowed

 

 

The minimum speed at which the fan motors will spin.

 

 

20% (NEMA Motors) 

10%(EC Type Fans)

 

 

Min. Shutoff Timer 

The amount of time that must elapse whenever the fan 
speed reaches the minimum allowed percentage before 
the fans are turned off.  

30 seconds 

Min. Shutoff Offset 

The temperature offset below the setpoint before the fans 
are turned off.  

2.0 °F

 

Table 12  

The parameters of the Fan Speeds Screen. 

 

  

  

 

 

 

 

Figure 31

 

 

 

Summary of Contents for eco-Air Series








































Reviews:

No comments

Brands by name

Popular brands

Load more brands