manualshive.com logo in svg

EUTECH INSTRUMENTS CyberScan pH 300, Instruction Manual, Page: 39 / 52

Share
Download
EUTECH INSTRUMENTS CyberScan pH 300 Instruction Manual Download Page 39

 

 

36

12. Press the MI/

▲

 or MR/

▼

 keys to toggle to the 

correct hour. Note the “AM” and “PM” indicator on 
the lower portion of the display.  

13.  Press the ENTER key to confirm the hour and 

move to “minute” selection. The “minute” digits will 
flash.   

14. Press the MI/

▲

 or MR/

▼

 keys to toggle to the 

correct minutes.  

15.  Press the ENTER key to confirm the minutes and 

move to “second” digits will flash. See Figure 35.  

16. Press the MI/

▲

 or MR/

▼

 keys to toggle to the 

correct seconds.  

17.  Press the ENTER key to confirm the 

seconds and return to “century” selection.  

18.  Press the CAL/MEAS key to return to the 

subgroup menu. Press the CAL/MEAS key 
again to return to measurement mode.  

 

NOTES 

Press the CAL/MEAS key at any point while 
setting the time to return to the subgroup menu.  

 

Figure 36 - P5.0: Select time (pH 310 

meter only) 

Figure 35 - P5.0: Setting month and 

date (pH 310 meter only) 

Summary of Contents for CyberScan pH 300





















































Reviews:

No comments