background image

 

  Warning 

1.

 

This heater is for general indoor home heating only. 

2.

 

Place  heater  in  a  well  ventilated  area  away  from  flammable 
materials and air cans. 

3.

 

Place  the  heater  on  a  steady  and  even  floor.  Do  not  hang  or 
install on wall. 

4.

 

Please  use  individual  socket  if  the  output  rated  current  is  more 
than 10A. Do not use the same socket with other equipment to 
avoid  overloading.  Make  sure  plug  is  properly  inserted  into  the 
socket. 

5.

 

Supervise usage when in use with children and elderly. 

6.

 

Unauthorized disassembly, modification, repair are prohibited.   

7.

 

Do not operate or touch the plug with wet hands. 

8.

 

Use 230-240V~ AC power.   

9.

 

Ensure filters are clear and properly cleaned. 

10.

 

Do not move the heater when operating.   

11. Do not cover the heater or the air vents. 
12. Be careful the device will be very hot when in operation. 
13. Please unplug the device when not in use. 
14. Do not use any aerosols near the device when in operation. 
15. If there is a burning smell, stop using and unplug the power cord. 

Contact your retailer.   

16. Do not use in the batch room or near water.   
17. Do not allow children to play with this heater. 
 

 

Summary of Contents for 25963













Reviews: