Eurotherm 2116i, User Manual

Page: 7 / 12

O
RDERING
C
ODE
The indicator is supplied configured to the ordering code shown below.
1 2 3 4 5 6 7 8 9 10 11 12
T
ECHNICAL
S
PECIFICATION
Display 4 digit, green. 10mm high characters
Supply voltage High voltage unit: 100Vac -15% to 10%, 48-62Hz. Power consumption: 5Watts maximum
Low voltage unit: 24Vdc or ac -15%, +20% DC to 62Hz, Power consumption: 5Watts maximum
Operating
ambients 0 to 55
o
C. 5 to 95%RH, non condensing
Storage
temperature -20
o
C to +75
o
C.
Output ratings Relay(isolated): Maximum: 264Vac, 2A resistive. Minimum: 12Vdc, 100mA
Logic I/O: 9Vdc at 18mA (non-isolated from sensor input). Can be used as alarm output or alarm
acknowledge input
Calibration
accuracy ±
1
o
C or
±
0.25% of reading whichever is greater
Cold junction
compensation >30 to 1 rejection of ambient temperature change. Uses INSTANT ACCURACY
TM
cold junction sensing
technology to eliminate warm-up drift and respond rapidly to ambient temperature changes.
Input filtering Off to 999.9 seconds
EMC standards Emissions and immunity standard EN61326 suitable for industrial environments.
Safety standard EN 61010. Installation category II. (Voltage transients on the power supply must not exceed 2.5kV).
Pollution degree 2. All isolated inputs and outputs have reinforced insulation to protect against electric
shock.
Atmosphere Not suitable for use above 2000m or in explosive or corrosive atmospheres
Panel sealing IP65 (EN 60529), or NEMA 4X
7. Sensor input 8 & 9. Display range and
Setpoint min & max limits
Thermocouples
°
C
°
F
J Type J -210 to 1200 -340 to 2192
K Type K -200 to 1372 -325 to 2500
T Type T -200 to 400 -325 to 750
L Type L -200 to 900 -325 to 1650
N Type N -200 to 1300 -325 to 2370
R Type R -50 to 1768 -58 to 3200
S Type S -50 to 1768 -58 to 3200
B Type B 0 to 1820 32 to 3308
P Platinell II 0 to 1369 32 to 2496
Resistance thermometer
Z Pt100 -200 to 850 -325 to 1562
Custom downloaded inputs
C Type C -W5%Re/W26%Re
(default custom sensor)
0 to 2319 32 to 4200
D Type D - W3%Re/W25%Re 0 to 2399 32 to 4350
E E thermocouple -200 to 999 -325 to 1830
1 Ni/Ni18%Mo 0 to 1399 32 to 2550
2 Pt20%Rh/Pt40%Rh 0 to 1870 32 to 3398
3 W/W26%Re (Engelhard) 0 to 2000 32 to 3632
4 W/W26%Re (Hoskins) 0 to 2010 32 to 3650
5 W5%Re/W26%Re
(Engelhard)
10 to 2300 50 to 4172
6 W5%Re/W26%Re(Bucose) 0 to 2000 32 to 3632
7 Pt10%Rh/Pt40%/Rh 200 to 1800 392 to 3272
8 Exergen K80 I.R.
Pyrometer
-45 to 650 -49 to 1202
Process inputs (linear)
M -9.99 to +80mV Scalable -999 to 9999
Y 0 to 20mA Scalable -999 to 9999
A 4 to 20mA Scalable -999 to 9999
V 0 to 10Vdc ( input adapter
required)
Scalable -999 to 9999
3. Supply voltage
VH 85-264Vac
VL 20 -29V dc or ac
4. Manual
XXX None
ENG English
FRA French
GER German
NED Dutch
SPA Spanish
SWE Swedish
ITA Italian
5. Logic I/O
XX Disabled*
Logic input
AC Alarm ack/reset
KL Keylock
Non-latched alarms
FH High alarm 1
FL Low alarm 1
Latched alarms
HA High alarm 1
LA Low alarm 1
NW New alarm
2. Function
ND Indicator only*
AL Indicating alarm unit
1. Model Number
2132
6. Alarm Relay Output
i 1/8 DIN indicator
2116i ¼ DIN indicator
XX Disabled*
Non-latched alarms
FH High alarm 2
FL
Low alarm 2
AL High alarm 2 & low alarm 3
Latched alarms
HA High alarm 2
LA
Low alarm 2
AA High alarm 2 & low alarm 3
NW New
alarm
10. Units
°
C
C K Kelvin
°
F
F X Linear input
11. External relay module
XX Not
fitted
R7 Fitted (Operated by the logic
output)
12. Input Adaptor
XX None
V1 0-10Vdc
A1 0-20mA sense resistor
(2.49
Ω
. 0.1%)
‘ND’ (Indicator only) is specified in the function field, then XX must be entered in the Logic I/O and alarm 2 relay fields. *If
2116i.2132i – Applies to versions 1.3 & 1.4 5 HA026248 – Issue 4 08/07