Issue 1, Apr-98 Applies to software version 1.0
-
4
-
HA026277
The
05/ (Promote) option
Up to twelve commonly used parameters can be ‘promoted’ into
the HOME list. This will give the operator quick access to them
by simply pressing the
button. This feature, used in
combination with ‘hide’ and ‘read only’, allows you to organise
the way in which you want your indicator formatted.
Select EDIT level to hide, reveal or promote parameters as below:
The parameter
) will now appear in the HOME list. Repeat
the procedure for any other parameters you wish to promote.
To de-promote a parameter go to
O6 level, select the parameter
from the relevant list and change the choice from
05/ back to
)65, 5 or #O.
Returning to Operator level
Repeat the above procedure for all the parameters you wish to hide,
promote, or make read-only then return to operator level:
Your indicator has been calibrated for life against known reference
sources in the factory. User calibration allows you to apply offsets
to compensate for sensor and other system errors. You can apply a
simple fixed offset over the whole display range using the
parameter
in the O0 list, or alternatively, you may apply a 2-
point calibration as follows:
•
Press
until you reach the
O0 list
•
Press
until you reach the
)D0 parameter
•
Press
or
to enter the password. The factory default
password is 3.
0 will be displayed when correct.
•
Press
to reach the
) parameter
•
Press
or
to select
85 (6 will restore the
factory calibration)
•
Press
to select
0.6D)
•
Press
or
to adjust the value at which you wish to
apply the low calibration point offset. (eg zero)
•
Press
to select
D)
•
Press
or
to set the low calibration point offset.
•
Repeat the above to select and adjust
0.6D# and D#
The graph below shows the effect of a low and high point offset.
These warn that a fault exists in either the indicator or the
connected devices.
Alarm
What it means
What to do about it
EE.Er
Electrically Erasable
Memory Error: The
value of an operator
or configuration
parameter has been
corrupted.
This fault will automatically
take you into configuration
level. Check all of the
configuration parameters
before returning to operator
level. Once in operator level,
check all of the operator
parameters before resuming
normal operation. If the fault
persists or occurs frequently,
contact Eurotherm Controls.
S.br
Sensor Break: Input
sensor is open
circuit.
Check that the sensor is
correctly connected.
LLLL
Out of range low
reading
Check the value of the input
HHHH
Out of range high
reading
Check the value of the input
Err1
Error 1: ROM self-
test fail
Return the indicator for repair
Err2
Error 2: RAM self-
test fail
Return the indicator for repair
Err3
Error 3: Watchdog
fail
Return the indicator for repair
Err4
Error 4: Keyboard
failure Stuck
button, or a button
was pressed during
power up.
Switch the power off and then
on without touching any of the
indicator buttons.
Value at which you
wish to apply the
offset
Display Offset
Applied
Factory calibration
0.6D#
D#
D)
0.6D)
User calibration
High alarm 2 has been selected.
When
or
is pressed, instead of displaying
the parameter value, its availability in Operator
level is shown as follows:
)65
The parameter will be alterable
#O
The parameter will be hidden.
5
The parameter will be read-only
05/
The parameter will be ‘promoted’
into the HOME list (see below).
1. Press
until you reach the
list
heading
2. Press
until you reach
!/6/
3. Press
or
to select
15
4. Press
to return to Operator level
0
/
Press
or
to enter the password. The
factory default password is 1. ‘
0’ will be
displayed momentarily when the correct
password has been entered.
Press
Press
until the Access List Heading is reached.
You are now in Edit level.
Press
and
to select a parameter in
the normal way.
If no button is pressed for 45 secs the
display returns to operator level.
Press to return to the Access list header.
Press
or
to select
‘
O6
’
level.
Other options are:
05
Operator level - shows selected
parameters
9))
Reveals the ‘FULL’ set of parameters
/.
Gives access to configuration level.
(see CONFIGURING THE INDICATOR)
O6
!/6/
Press
Edit Level Example:
#O
#
05
!/6/
Low alarm 1 has been selected
Press
or
to choose
05/.
Promote Level Example:
05/
)
T
O
H
IDE
, R
EVEAL AND
P
ROMOTE
P
ARAMETERS
U
SER
C
ALIBRATION
D
IAGNOSTIC
A
LARMS