manualshive.com logo in svg

EuroTel ETL0W474G, Operating And Technical Manual

Share
Download
EuroTel ETL0W474G Operating And Technical Manual Download Page 32

ETL0W474G

Rev. 004

4 )  

4 )  

4 )  

4 )  Alarm and Warning Events

Alarm and Warning Events

Alarm and Warning Events

Alarm and Warning Events

In ETL0W474G many measures have different threshold values configured and stored in the EEPROM. 
Different values are configured for DTV and ATV operating mode.

When the actual values of these measures are not located within the thresholds set, a warning or an 
alarm event occurs. The occurrence of warning and alarm events depends on the type of threshold 
violated.

The following explains what happens to the Amplifier when a warning or an alarm event occurs.

WARNING EVENT:

WARNING EVENT:

WARNING EVENT:

WARNING EVENT:

Amplifier operation is not interrupted. The power supply of the final modules of the amplifier is reduced 
by about 13%. This reduces by about 25% the RF output power of the ETL0W474G Amplifier.

ALARM EVENT:

ALARM EVENT:

ALARM EVENT:

ALARM EVENT:

Shutdown of the power supply of the final modules of the amplifier. The amplifier is disabled, no RF 
output power is available.

The threshold values of the measure can be seen by RS-232 connection. 

An example of what appear on PC's display is reported in Figure 9. NOTE: Values shown in this picture 

NOTE: Values shown in this picture 

NOTE: Values shown in this picture 

NOTE: Values shown in this picture 

are for demonstration only, they should be not real values.

are for demonstration only, they should be not real values.

are for demonstration only, they should be not real values.

are for demonstration only, they should be not real values.

Figure 9: Example of PC's display for RS-232 connection.

Warning and alarm events may occur immediately or delayed with respect to the instant in which the 
threshold is violated. Delayed warning events occur 10 seconds after the threshold violation whereas 
delayed alarm occurs 5 second after the threshold violation.
For some measures is also provided a “Low” threshold value. This is the threshold at which the value of 
the measure must be drop after a warning or an alarm event to restore the standard operating mode. If 

Page 32

CMAN0W474G

Oct 2013

Summary of Contents for ETL0W474G








































Reviews:

No comments

Brands by name

Popular brands

Load more brands