3
Heater
1.
2.
3.
4.
NOTE:
5. Drill the 3 holes to 34mm depth with 6mm diameter drill bit.
6.
Accessories
1.
Slider Rail.
2.
NOTE:
the top of the Heater.
3. Drill 2 holes and mount the Shower Accessories with wall plugs and screws provided.
4. Insert the Rail Support Covers onto the Rail Supports.
Heater Inlet and Outlet
and Hand Shower set provided.
NOTE:
1. Connect the Stop Valve to the Heater Inlet with Rubber Washer provided. Use proper
2. Connect the incoming water pipe (1/2” BSP) to the Stop Valve.
3. Make sure to put the Mesh Filter between Stop Valve and incoming water pipe.
4.
between the heater inlet pipe and incoming water pipe.
5.
NOTE:
WARNING!
• The heater tank must be
up with water before the power supply is
switched on.
This is to prevent damage to the
element.
6. Connect the PVC Hose and Hand Shower to the heater outlet. Be sure to put in the
Rubber Washer.
7. Hook the Hand Shower to the Adjustable Shower Holder and adjust it to your desired
8. Check for any water leakage.
WARNING!
• The water inlet and outlet must be installed correctly, otherwise the Heater
cannot
• Do not use plumbing clement on
If necessary, use only thread or
sealing tape.
4
Electrical
WARNING!
• The product must be earthed.
Improper grounding could cause electrical shock.
• Make sure the electrical mains is switched before carrying out any electrical
work.
• Refer to Wiring Loading Table for the correct cable size.
• Use at least 2.5mm
2
double coated cable.
• Lead the power cable from the MCB to a “ON/OFF” double pole linked switch
having a contact
of at least 3mm in all poles outside the bathroom,
then lead a cable connected to terminal block inside the unit.
(see Fig. 2)
1. Insert the cable through the rubber grommet for side entry or wall embedded entry.
2.
BROWN or RED --- LIVE ( L )
BLUE or BLACK --- NEUTRAL ( N )
GREEN or GREEN/YELLOW --- EARTH ( )
WARNING!
• Ensure the wiring
is correct.
3. Pull out the Temperature Control Knob from the Front Cover.
4. Replace the Front Cover.
5.
Heater.
Outlet
Inlet
Rubber
Washers
M
A
X
M
A
X
OFF
M
A
X
OFF
Fig.
F
1
ig. 3
Fig. 2
Note:
Refer to Wiring Loading
Table for electrical loading
and correct size of wire
conductor
.
Brown or Red = Live (L)
Blue or Black = Neutral (N)
Green or Green/Yellow
= Earth ( )
Rail Support Cove
Soap Dish
ĂƵƟŽŶ͗tĂƌƌĂŶƚLJŵĂLJďĞǀŽŝĚŝĨƵŶĂƵƚŚŽƌŝƐĞĚƵƌŽƉĐĞŝŶƐƚĂůůĞƌŝƐƵƐĞĚ͘
WƌŽĚƵĐƚƐĂĨĞƚLJǁŝůůďĞĐŽŵƉƌŽŵŝƐĞĚŝŶƚŚĞĞǀĞŶƚŽĨǁƌŽŶŐǁŝƌŝŶŐŽƌŝŶƐƚĂůůĂƟŽŶ͘
3
Heater
1.
2.
3.
4.
NOTE:
5. Drill the 3 holes to 34mm depth with 6mm diameter drill bit.
6.
Accessories
1.
Slider Rail.
2.
NOTE:
the top of the Heater.
3. Drill 2 holes and mount the Shower Accessories with wall plugs and screws provided.
4. Insert the Rail Support Covers onto the Rail Supports.
Heater Inlet and Outlet
and Hand Shower set provided.
NOTE:
1. Connect the Stop Valve to the Heater Inlet with Rubber Washer provided. Use proper
2. Connect the incoming water pipe (1/2” BSP) to the Stop Valve.
3. Make sure to put the Mesh Filter between Stop Valve and incoming water pipe.
4.
between the heater inlet pipe and incoming water pipe.
5.
NOTE:
WARNING!
• The heater tank must be
up with water before the power supply is
switched on.
This is to prevent damage to the
element.
6. Connect the PVC Hose and Hand Shower to the heater outlet. Be sure to put in the
Rubber Washer.
7. Hook the Hand Shower to the Adjustable Shower Holder and adjust it to your desired
8. Check for any water leakage.
WARNING!
• The water inlet and outlet must be installed correctly, otherwise the Heater
cannot
• Do not use plumbing clement on
If necessary, use only thread or
sealing tape.
4
Electrical
WARNING!
• The product must be earthed.
Improper grounding could cause electrical shock.
• Make sure the electrical mains is switched before carrying out any electrical
work.
• Refer to Wiring Loading Table for the correct cable size.
• Use at least 2.5mm
2
double coated cable.
• Lead the power cable from the MCB to a “ON/OFF” double pole linked switch
having a contact
of at least 3mm in all poles outside the bathroom,
then lead a cable connected to terminal block inside the unit.
(see Fig. 2)
1. Insert the cable through the rubber grommet for side entry or wall embedded entry.
2.
BROWN or RED --- LIVE ( L )
BLUE or BLACK --- NEUTRAL ( N )
GREEN or GREEN/YELLOW --- EARTH ( )
WARNING!
• Ensure the wiring
is correct.
3. Pull out the Temperature Control Knob from the Front Cover.
4. Replace the Front Cover.
5.
Heater.
Outlet
Inlet
Rubber
Washers
M
A
X
M
A
X
OFF
M
A
X
OFF
Fig.
F
1
ig. 3
Fig. 2
Note:
Refer to Wiring Loading
Table for electrical loading
and correct size of wire
conductor
.
Brown or Red = Live (L)
Blue or Black = Neutral (N)
Green or Green/Yellow
= Earth ( )
Rail Support Cove
Soap Dish
ĂƵƟŽŶ͗tĂƌƌĂŶƚLJŵĂLJďĞǀŽŝĚŝĨƵŶĂƵƚŚŽƌŝƐĞĚƵƌŽƉĐĞŝŶƐƚĂůůĞƌŝƐƵƐĞĚ͘
WƌŽĚƵĐƚƐĂĨĞƚLJǁŝůůďĞĐŽŵƉƌŽŵŝƐĞĚŝŶƚŚĞĞǀĞŶƚŽĨǁƌŽŶŐǁŝƌŝŶŐŽƌŝŶƐƚĂůůĂƟŽŶ͘
