background image

AS/NZ 1716 : 2012 Lic 40344

SAI Global

FITTING INSTRUCTIONS FOR USE

Craftsman Particulate Pre-Filter 713 is used in conjunction with Craftsman Gas/Vapour filter ABEK 719, for protection  
against mechanically and thermally generated particles and clogging by sanding, polishing dust, or paint particles.
• To be used with 713R Retainers to connect the 713 filter to the 719 filter.

PARTICULATE 

PRE-FILTER P2

For use against  

both mechanically  

and thermally  

generated particulates.

C713

2

Euromarc 711 Series Respirator

When generating certain  

dusts, mists and fumes such  

as sanding, grinding, cutting,  

drilling metal, masonry,  

wood and concrete.

713

PARTICULATE 
PRE-FILTER P2

713

AS/NZ 1716 : 2012 Lic 40344

SAI Global

WARNING

•  Always be sure that your respirator is: a) suitable for all 

expected respiratory hazards in the workplace; b)  your 
respirator is fitted properly – refer to manufacturer’s 
instructions; c)  filter is replaced when necessary.

•  Do not use for respiratory protection against unknown airborne 

contaminants or when concentrations of contaminants are 
unknown or as protection against substances immediately 
dangerous to life or health.

•  Do not modify or alter filters or face-pieces.    

 

 

•  Use with Euromarc 710 series respiratory. 
•  If in doubt about the correct use or suitability of this device for 

any application, consult your supervisor, occupational health 
professional or contact Euromarc.

•  Always check the filters have not exceeded  

the use-by date.

•  Provides P3 protection only with full  

face-piece espirator, and P2 protection  
with half face-piece respirator.

PARTICULATE 

FILTER GP3

For use against both  

mechanically and thermally  

generated particulates (half face 

mask). For use against all  

particulates including highly  

toxic materials (full face mask).

C718

2

Euromarc 711 Series Respirator

When generating dusts and fumes  

with sanding, grinding, cutting,  

polishing, or particles form welding  

or fabricating. Working with toxic 

particulates such as mould remediation. 

Also for spraying pesticides or herbicides 

with vapour pressure < 1.3 Pa @ 25°C.

718

PARTICULATE 
FILTER GP3

718

Summary of Contents for CRAFTSMAN 711 Series

Page 1: ...filters Never modify or alter this product doing so could jeopardize your safety While materials in this mask do not commonly cause allergic reactions if you notice any reaction or irritation cease use and seek medical advice P3 rated protection can only be achieved when using a full face mask irrespective of filter choice PREPARATION FOR USE Check that the mask is complete undamaged and assembled...

Page 2: ...fit DO NOT enter the hazardous area It is recommended that wearers should be fit tested in accordance with AS NZS 1715 MAINTENANCE AND CLEANING Euromarc recommends cleaning the mask after each use Use designated respirator cleaning wipes and wipe the face seal and internal surfaces Or remove the filters and wash in warm clean water below 50 degrees C Leave to air dry at room temperature in a clean...

Page 3: ... not use for respiratory protection against unknown airborne contaminants or when concentrations of contaminants are unknown or as protection against substances immediately dangerous to life or health Do not modify or alter filters or face pieces Use with Euromarc 710 series respiratory If in doubt about the correct use or suitability of this device for any application consult your supervisor occu...

Page 4: ...e 1 4 turn clockwise to attach fig 9 10 CAUTION Over rotation will result in damage to the filter and facepiece Note These filters are supplied in pairs of identical classes and type and must be fitted used and replaced at the same time 3 Leave work area immediately check integrity of respirator and replace any parts if a damage has occurred or is apparent b dizziness illness or irritation occurs ...

Reviews: