1
.
2a.
Extension Hose
Tool Connector
4. Grasp by steam mop handle and detent to begin mopping.
5. Begin cleaning by slowly moving the unit over the floor surface. Moisture on the
floor is normal when cleaning.
6. When the Zero Bend Series Steristeam stops emitting steam, turn the unit off
and unplug. Verify if there is water in the tank. If empty, refill the water tank.
IMPORTANT: Sanitizing on timber floors is not recommended, as prolonged
application of steam in one area increases the risk of damage to the surface
treatment on timber floors, especially in areas with regular foot traffic and
direct sunlight, which will wear down timber floor surface treatments, making
it more susceptible to steam damage.
USING THE STEAM POD
NOTE: When changing from mopping to hand pod use, press the On/Off
button to turn the steam OFF and wait ten seconds.
1. Make sure the steam is OFF and wait ten seconds.
2. Press the Lift-off release button and pull the hand pod out by the handle.
3. With the connector or extension hose attached to hand pod, connect the tool
to the opening.
4. Turn the tool in order to lock into place.
5. Press the ON/OFF button. Once the ready light stops blinking and is solid, the
heat up is completed.
6. Press the Hi/Lo button, depending on volume of steam desired.
7. ONLY then will the hand-held unit steam.
NOTE: The handheld steam pod will not operate without the proper
attachments. You must have the connector or extension hose attached for the
steam to emit. A safety feature has been designed to prevent steam emission
without the connector or extension hose.
NOTE: Turn the steam OFF before removing or connecting tools and
accessories.
Use of distilled or demineralized water is recommended, to prolong the life of your hard floor cleaner.
Tip
Use of distilled or demineralized water is recommended, to prolong the life of your hard floor cleaner.
Tip
GETTING READY
1. Attach pad to the mop foot. (Elastic band will secure pad on the foot.) *This may
already be attached.
2. Fill the water tank.
a.
The water tank opening is located on the side of the water tank. Remove the
cover and use water cup to fill. NOTE: Do not overfill or water may spill. Room
temperature water may provide better results.
b.
Close the tank cover and press down firmly.
3. Pull and twist the cord holder clockwise to unwrap the power cord completely
and plug into an outlet as described on the Important Safety Instructions page.
NOTE: Do not use chemicals in the water tank of your Zero Bend Series
Steristeam.
NOTE: Upon the first use of your Zero Bend Series Steristeam or first use after
refilling the water tank, the pump may make a ‘knocking’ sound. This is normal
and could last up to 30 seconds.
USING YOUR STEAM MOP
The floor mop can be used on hard floors. For best results, vacuum the floor first to
clear dust and small debris before using your steam mop. Your Zero Bend Series
Steristeam floor cleaner is designed to clean hard flooring, such as ceramic tile, vinyl,
marble, stone and sealed hard wood floors. Use on waxed or some unwaxed floors
may result in a diminished glossiness. The Zero Bend Series Steristeam is not for use
on unsealed wooden floors. For best results, test in an inconspicuous area and check
the care instructions from your flooring manufacturer.
1. Plug the unit in and wait 30 seconds for it to heat up. The “ready” light will blink
while the steam mop heats up. The “ready” light will be solid and lit up when heat
up is complete. Press the On/Off button first. Then choose HI or LO steam. HI (for
durable floors or sticky messes) or LO (for delicate floors or everyday cleaning).
2. Trigger is ‘steam on demand’. When steam is wanted, pull trigger. When you do
not want steam, release trigger.
3. To be sure to sanitize an area of your floor, use the microfibre cloth pads and slowly
and evenly stroke your steam mop back and forth at least three times over the area,
using continuous steam. For best results, remove the pad and wash after use.
INSTALLING EUROCLEAN
ZERO BEND SERIES STERISTEAM
INSTALLING EUROCLEAN
ZERO BEND SERIES STERISTEAM
7
8