Euro-Pro SHARK HV118 Owner'S Manual Download Page 4

OPERATING INSTRUCTIONS

PRECAUTIONARY MEASURES

7

Debris

Screen

6. “TapClean” the Debris 

Screen or rinse under 

a faucet until clean. 

Remember that the 

Debris Screen must be 

completely air dried for 

24 hours before 

reinstalling in the vacuum.

7. To re-assemble the HEPA filter 

assembly, first insert the HEPA 

filter onto the dust cup cover 

making sure to push it all the way 

in. Then insert the debris screen 

again making sure that it is pushed 

all the way up against the dust cup 

cover. 

8. When replacing the dust cup cover 

with the HEPA filter assembly 

into the dust cup, make sure that 

the tab on the 

dust cup cover 

is fully aligned 

with the tab 

indentation on 

the dust cup 

handle otherwise 

the seal will not 

be complete 

and the unit will not

function properly.

PLEASE NOTE

: The white pleated 

filter material in the HEPA Dust Cup 

Filter will discolor over time -This is 

NORMAL and will NOT affect the 

performance of the filter. If the HEPA 

Dust Cup Filter is 

properly "TapCleaned” 

after each use and 

suction does not 

return to 100%, then 

we suggest that the 

HEPA filter be 

“TapCleaned” 

vigorously until no

more dust can be 

removed, then rinsed under the faucet 

and allowed to air dry for 24 hours 

before refitting into the vacuum. (Fig. 

A) Wash once a month or when 

suction appears reduced.

Fig. A

Wash once a 

month or when 

suction appears 

reduced.

Warning:

Allow 24 

hours for drying 

before replacing in 

unit.

Changing & Cleaning the Exhaust 

Filter

The exhaust filter is a washable filter but 

should be replaced every three (3) 

months depending on usage.

1. Remove the exhaust filter cover from 

the rear of the unit. 

2.  Rinse the exhaust filter in 

lukewarm water and dry the 

filter completely. Do not use 

a washing machine to rinse 

the filter. Do not use a 

hair dryer to dry it. Air dry 

ONLY 

for 24 hours. Never 

operate the vacuum without 

the exhaust filter in place.

3. When the filter is dry, replace 

into the unit and replace the exhaust 

filter cover over it. 

4.  A severely soiled or clogged filter 

should be thoroughly washed with 

fresh tepid water. A mild detergent 

can be used if required.

IMPORTANT

:

This unit is equipped 

with a motor protective thermostat.  If for 

some reason the vacuum cleaner should 

overheat, the thermostat will 

automatically turn the unit off.  Should 

this occur:

• Push the On/Off button once.

• Disconnect the plug from the power 

source.

• Check the source of overheating 

problem. (i.e. clogged hose or filter)

• If clogged hose or filter is found, unclog 

the hose and replace the filter.

• Wait at least 45 minutes before 

attempting to reuse the vacuum.

• After unit has cooled down for 45 

minutes, plug in the cleaner and push 

the On/Off button. The vacuum should 

start again.

• If the vacuum still does not start, 

contact customer service at 

1 (800) 798-7398.

Motor Thermostat

When the Intelli-Sense Filter Monitor

TM

lights up, it means that the dust cup is full 

or filter needs cleaning.  You must empty 

the dust from the dust cup and clean the 

HEPA dust cup filter right  away. 

Intelli-Sense Filter MonitorTM

CAUTION

:

The suction hole must be 

open, free of any obstructions at all 

times.  Otherwise, the motor will overheat 

and could become damaged.

5. Vigorously “TapClean” 

the HEPA Dust Cup 

Filter on a hard 

surface until no more 

dust is observed 

falling out from 

between the pleats of 

the filter. 

Important

:

If the suction opening in the unit, the hose or the extension tubes 
become blocked, switch off the vacuum cleaner and remove the blocking 
substance before you start the unit again.

5.

When pulling out the power plug 
from the wall outlet, pull the plug 
not the power cord.

1.

Do not operate the vacuum 
cleaner to close too heaters, 
or radiators.

6.

Do not pick up anything that is 
burning or smoking such as 
cigarettes, matches or hot ashes.

2.

Before inserting the power plug 
into the wall outlet, make sure that 
your hands are dry.

7.

Do not use without dust cup filter or 

exhaust filter in place.

8.

Before you start vacuuming, 
make sure to remove large or 
sharp objects that might 
damage the vacuum.

3.

Do not vacuum any liquids.

4.

Keep hair, loose clothing, fingers, 

feet and all parts of body away from 
openings. 

2

Reviews: