2
GETTING TO KNOW YOUR TRANSFORMER VAC
Technical Specifications
Voltage:
120V., 60Hz.
Power:
10 Amps
1.
Hand Grip
2.
Telescopic Tube
3.
Locking Button
4.
Flexible Hose
5.
Dust Cup Release Button 1
6.
Dust Cup Handle
7.
Dust Cup (Container)
8.
Main Unit
9.
Intelli-Sense
TM
Filter
Monitor
10. Exhaust Filter Cover
11. On/Off Switch
12. Power Cord
13. Floor Brush Release Button
14. Floor Brush
15. Crevice Tool
16. Dusting Brush
17. Telescopic Tube Release
Button
18. Dust Cup Release Button 2
19. Cord Hook Release
20. Hose Connector
21. Telescopic Hose
Extension Tube
22. Air Driven Turbo Brush
23. Pet Hair Removal Brush*
24. Shoulder Strap (not shown)
21
22
*Illustration may differ from actual product.
OPERATING INSTRUCTIONS
IMPORTANT
:
This unit is equipped
with a motor protective thermostat. If
for some reason the vacuum cleaner
should overheat, the thermostat will
automatically turn the unit off. Should
this occur:
• Push the On/Off button once.
• Disconnect the plug from the
power source.
• Check the source of overheating
problem. (i.e. clogged hose or
filter)
Motor Thermostat
• If clogged hose or filter is found,
unclog the hose and replace the
filters.
• Wait at least 45 minutes before
attempting to reuse the vacuum.
• After unit has cooled down for
45 minutes, plug in the cleaner
and push the On/Off button. The
vacuum should start again.
• If the vacuum still does not start,
contact customer service at
1-800-798-7398.
TROUBLE SHOOTING GUIDE
PROBLEM
POSSIBLE REASON
POSSIBLE SOLUTION
VACUUM WILL
NOT OPERATE
1.
Power cord not firmly plugged into
outlet.
2.
No power in wall outlet.
3. Needs
servicing.
4.
Thermostat has tripped.
1.
Plug unit in firmly.
2.
Check fuse or breaker. Replace
fuse/reset breaker.
3. Call
1-800-798-7398.
4.
Turn the unit off and unplug from
outlet. Allow unit to cool down,
then restart.
VACUUM WILL
NOT PICK-UP OR
SUCTION POWER
IS WEAK
1.
Dust cup is full.
2. Unit
clogged.
3.
HEPA Filter needs cleaning or
replacing.
4.
Debris screen needs cleaning.
5.
Filters need cleaning
1.
Empty and clean dust cup.
2.
Turn unit off and unplug from
wall outlet. Remove Dust Cup
Filter and check for object(s) in
air duct and remove.
3.
Clean or replace HEPA Filter.
4.
Clean debris screen.
5. Clean
Filters
TURBO BRUSH
DOES NOT
ROTATE OR
ROTATES
SLOWLY
1.
Dust cup is full.
2.
Rotating brush or elbow is
obstructed.
3. Belt
is
broken.
4. Hose
obstructed.
5. Debris
screen
is
clogged.
6.
Filters need cleaning.
1. Empty
dust
cup.
2. Clear
obstructions.
3. Call
1-800-798-7398.
4. Clear
obstruction.
5.
Clean debris screen.
6. Clean
all
filters.
DUST ESCAPING
FROM VACUUM
1.
Dust cup is full.
2.
Dust Cup is not installed correctly.
1.
Empty and clean dust cup.
2.
Review Dust Cup instructions.
VACUUM, HOSE
OR BRUSHES
WILL NOT PICK-UP
1. Hose
clogged.
2.
Dust cup is full.
1. Remove
hose
and/or
brushes.
Remove obstruction from hose
and /or brush.
2.
Empty and clean dust cup.
9
