Jewel Module
12
Jewel Module
5
Removing the fascia
• Turn the fan power off, and removed the three pin plug from the power point.
• Open the door 25mm and lift door off hinge, place door on a soft flat surface.
• Undo x4 M8 button head cap screws which attach the fascia to the main firebox.
• Gently lift the fascia away from the front of firebox, but do not pull away fascia completely, leave the fascia rest on the hinge while
removing the fan switches.
• With the fascia resting on hinge, reach behind the switch panel and undo x2 wing nuts and remove switch panel.
• With switch panel removed, fascia can now be completely moved away from the heater to gain access to the fan and wiring looms.
Installation
(Continued)
The Eureka Jewel Module can be installed into various installations depending
on desire, or practicality. Figure 3 shows the appliance when installed
on a Bench. Use this image as a guide for inspiration, or installation tips.
All installations must conform as per dimensions on page 4, when installing on
or adjacent to combustible materials.
Under all circumstances, if installing the Eureka Jewel Module on a bench above a
floor comprising of combustible material, a minimum 6mm thick non-combustible
floor protector centred to the appliance at least 940mm wide, must extend 300mm
in front of the bench, and continue beneath the bench to meet the rear of the bench
or rear wall of the installation to conform to AS/NZS 2918:2001.
Take care not to scratch hearth, or bench during the installation process.
The bench is fitted with x4 levelling feet which will allow for any hearth or floor
unevenness.
1200
280
775
1200 Two Door Bench
Module Footprint
(top view)
Hole centres for fixing to bench
FRONT OF BENCH - APPLIANCE LOCATED CENTRALLY
97.5
580
260
97.5
Fixing Module to Bench
• With Module on pallet, back off 2x retaining screws and remove
pedestal filler panel (each side) to gain access to transport screws.
• Remove tek screws holding base of the appliance to the pallet.
• Using the Module footprint dimensional guide (figure 4), mark
out the transport bracket hole centre on the bench.
• Double check the hole centre dimensions by measuring the
existing hole positions in the base of the module before drilling.
• Upon confirming centre hole dimensions, drill 4x holes using a
4.5mm diameter drill bit. Remove all swarf when complete.
• If it is desired that the power cord should exit through the base
of the unit, a hole saw must be used (minimum 50mm diameter)
to create a hole as shown.
• Carefully removed Module from pallet, and locate on bench
over drilled holes. (Remove top plate, door, cast iron liners and
baffle system to reduce overall appliance weight)
• Using 4x supplied tek screws, attach Module to bench.
• If central hole has been cut, use pinch weld supplied to cover the
edges of the hole, to protect the power cord from damage.
Note: Do not pass the power cord through the hole in the centre
until after all four retaining screws have been fitted and the pinch
weld is installed.
• Secure the power cord to in the base of the unit using the cord
grip grommet, as shown in figure 5.
Figure 3
Basic Spare Parts
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
234933
230980
907424
917333
922334
230565
903903
234278
231030
233881
232037
213049
227074
906103
234101
910106
234016
234015
213151
906201
213146
917119
233884
230568-10
230980
907424
917333
922334
230565
203903
234278
231030
233881
232037
231049
227074
204184
906103
213321
221328
203651
234101
214289
213098
907400
212974
917209
234811
204184
203902
234935
233880
234936
231804
223625
231821
917203
903206
233882-01
233883-01
208177
903205
234939
203651
234016
234015
213151
906201
213164
917119
214289
213098
907400
212974
917209
231804
233882-01
233883-01
917203
903206
234811
203902
208177
903205
Ref. GPN Description
Ref. GPN Description
Module Assy
Hinge
Washer Flat 8 x 20
Screw Set M8 x 20
Screw Cap M8 x 20
Door Assembly
Twin Barrel Fan
Blanking Panel
Cast Iron Liner
Steel Baffle Plate
Switch - 2 Position
Switch - 3 Position
Switch Knob
Washer Flat 3/16” x 9/16”
Hinge Shim
Washer Star M8
Latch Block Shim
Catch Assembly
Screw Tek 10-16 x 16
Washer Flat 1/4“ x 3/4”
Wing Nut M6
Screw Set M5 x 20 C/S
Fascia Assy
Fascia Fill Panel
Hinge
Washer Flat M8 x 20
Screw Set M8 x 20
Screw Cap M8 x 20
Door Assembly
Twin Barrel Fan
Blanking Panel
Cast Iron Liner
Steel Baffle Plate
Switch - 2 Position
Switch - 3 Position
Switch Knob
Air Slide Bush
Washer Flat 3/16” x 9/16”
Rubber Grommet
Rubber Grommet Blank
Grommet Cord Grip
Hinge Shim
Thermostat Switch
Air Slide Spacer
Washer Flat 10 x 18
Air Slide Spring
Screw Set M6 x 20
Air Slide Link Spacer
Air Slide Bush
Screw Tek 10-16 x 25
Lower Infill Assembly
Top Panel
Infill Mount Bracket
Air Slide Rod
Rubber Bumper - Lower
Rubber Bumper - Upper
Screw Set M6 x 25
Nut Whiz Lock M6
Air Slide Panel
Air Slide Linkage
Screw Set M5 x 15
Nut Whiz Lock M5
Cord Grip Bracket
Grommet Cord Grip
Washer Star M8
Latche Block Shim
Catch Assembly
Tek Screw 10 -16 x 16
Washer Flat 1/4”x 3/4”
Wing Nut M6
Screw Set M5 x 20 C/Sunk
Thermostat Switch
Air Slide Spacer
Washer Flat 10 x 18
Air Slide Spring
Screw Set M6 x 20
Air Slide Rod
Air Slide Panel
Linkage Panel
Set Screw M6 x 25
Nut M6
Spacer - Air Slide Linkage
Tek Screw 10-16x25
Screw Set M5x15
Nut M5
Figure 12
$
$
6(&7,21$$
6&$/(
$,56/,'(/,1.$*(,167$//$7,21
%207DEOH5HVWUXFWXUHG
,7(0
3$571R
'(6&5,37,21
47<
6,=(
3$,17/,1($66<
$
+,1*(
$
:$6+(5)/$766[[
6&5(:6(70[[3%/$&.
6&5(:&$30[%87+'
'225$66<
$
)$1$66<7:,1:+((/
%/$1.,1*3$1(/,1%
$
%207DEOH5HVWUXFWXUHG
,7(0
3$571R
'(6&5,37,21
47<
6,=(
&$67,521/,1(55($5
$
%$))/(3/$7(
$
6:,7&+326,7,2163'721
21
)$16:,7&+63(('527$5<
.12%32:(56:,7&+
$
:$6+(5)/$7[[*
+,1*(6+,0
$
:$6+(567$50
,17(5/2&.,1*=3
/$7&+%/2&.6+,0
$
&$7&+$66(0%/<
$
6&5(:7(.[6(/)7
:$6+(5)/$7[*=3
$
187:,1*0=3
6&5(:6(70[&681.
%/$&.
6:,7&+7+(50267$7'(*
63$&(5$,56/,'(
$
:$6+(5)/$7[[PP
635,1*667((/$,56/,'(
6&5(:6(70[3+'%/$&.
63$&(5$,56/,'(/,1.$*(
$
%86+$,56/,'(
$
6&5(:7(.[6(/)7
,1),//:(/'$66(0%/<
$
7233$1(/67((/
$
,1),//02817%5$&.(7
$
52'$,56/,'(
$
*5200(7%8))(56
58%%(5%803(5%)
6&5(:6(70[[3+(;
*5=3
187:+,=/2&.)/$1*(066
3$1(/$,56/,'(
$
3$1(//,1.$*(
$
6&5(:6(70[32=,=3
1870:+,=/2&.)/$1*(
&/
&25'*5,3%5$&.(7
$
*5200(7&25'*5,3
0$7(5,$/
),1,6+
'5$:1
7,7/(
$33'
-,*
6+((7
2)
5(9 %< (&11R '$7(
5(9 %< (&11R '$7(
5(/($6('
'21276&$/(
$
6&$/(
3$571R
02'8/($66(0%/<
(85(.$-(:(/-,1'$5$63(&75(
77
(1*35
7+,6,1)250$7,21,6&21),'(17,$/$1'5(0$,167+(
3523(57<2)$)*$62137</7'81'(5&23<5,*+7/$:
$)*$62137</7',1&,19,&725,$
5(*,67(5('2)),&(
%/$.(675((7$5$5$7
9,&725,$
0$66NJ
7+,5'
$1*/(
352-(&7,21
67$1'$5'0(75,&72/(5$1&(681/(6663(&,),('27+(5:,6(
',0(16,2166+2:17+86RU
'5,//('+2/(6381&+('+2/(6$1*/(6
)25/$6(5&87&20321(176
)256+((7PP$1'81'(572/(5$1&(
)256+((7WRPP72/(5$1&(
)256+((7WRPP72/(5$1&(
77
470
290
%
%
6(&7,21%%
&
'(7$,/&
0$7(5,$/
),1,6+
'5$:1
7,7/(
$33'
-,*
6+((7
2)
5(9 %< (&11R '$7(
5(9 %< (&11R '$7(
5(/($6('
'21276&$/(
$
6&$/(
3$571R
02'8/($66(0%/<
(85(.$-(:(/-,1'$5$63(&75(
77
(1*35
7+,6,1)250$7,21,6&21),'(17,$/$1'5(0$,167+(
3523(57<2)$)*$62137</7'81'(5&23<5,*+7/$:
$)*$62137</7',1&,19,&725,$
5(*,67(5('2)),&(
%/$.(675((7$5$5$7
9,&725,$
0$66NJ
7+,5'
$1*/(
352-(&7,21
67$1'$5'0(75,&72/(5$1&(681/(6663(&,),('27+(5:,6(
',0(16,2166+2:17+86RU
'5,//('+2/(6381&+('+2/(6$1*/(6
)25/$6(5&87&20321(176
)256+((7PP$1'81'(572/(5$1&(
)256+((7WRPP72/(5$1&(
)256+((7WRPP72/(5$1&(
77
Fit pinch weld
to edge
Secure power cord
using cord grip grommet
Figure 4
Figure 5
Figure 6
