background image

To reduce the risk of electric shock, this appliance has a polarized plug (one blade wider than the other). This plug will fit
in a polarized outlet only one way. If the plug does not fit fully in the outlet, reverse the plug. If it still does not fit, contact a
qualified electrician to install the proper outlet. Do not change the plug in any way.

Afin de réduire le risque de choc électrique, cet appareil est muni d’une fiche polarisée (une des lames est plus large).
Cette fiche ne peut être insérée dans une prise polarisée que d’une seule façon. Si la fiche ne peut être insérée dans la prise,
retourner la fiche. Si la fiche ne peut toujours pas être insérée dans la prise, faire installer une prise adéquate par un
électricien qualifié. Ne pas modifier la fiche.

GENERAL INFORMATION

The cleaner is designed to pick up dirt and dust particles. Avoid picking up hard or sharp objects with the cleaner to prevent
cleaner damage and hose clogs with subsequent motor damage.

Service Information

The instructions in this booklet serve as a guide to routine maintenance. For additional service information telephone our toll
free number for the nearest Eureka Authorized Warranty Station. You should know the model, type and serial numbers
when you call:

USA: 1-800-282-2886

Mexico: 5670-6169

Canada: 1-800-282-2886

If you prefer, you can write to The Eureka Company, Service Division, 807 N. Main Street, Bloomington, Illinois 61701, USA.
In Canada write to The Eureka Company, 866 Langs Drive, Cambridge, Ontario N3H 2N7. Refer to The Eureka Limited
Warranty for complete service information.

DO NOT OIL the motor or the brush roll at any time. The bearings are permanently lubricated and sealed.

4

Rating Plate

The model, type, and serial numbers are indicated on the
rating plate located on the underneath side of the cleaner.
For prompt and complete service information, always refer
to these numbers when inquiring about service.

Model & Type__________________________

Serial No. _____________________________

MODEL               TYPE               SERIAL NO.

VOLTS                    AMPS.                     HERTZ

SERVICE INFORMATION: 1-800-282-2886

THE EUREKA COMPANY

BLOOMINGTON, ILLINOIS 61701

Thermal Cut Off

This vacuum cleaner has a special thermostat that protects the cleaner in case of motor overheating. If the cleaner suddenly
shuts off, push the rocker switch to off (O) and unplug the cleaner. Check the cleaner for a possible source of overheating
such as a full dust cup, a blocked hose or clogged filter. If these conditions are found, fix them and wait at least 30 minutes
before attempting to use the cleaner. After the 30 minute period, plug the cleaner back in and turn on the switch. If the cleaner
still does not run, then take it to a Eureka Authorized Service Center for repair.

Summary of Contents for 4880 Series





















Reviews: