Eureka Ergonomic ERK-EDK-GD Assembly Manual Download Page 2

When operating any electric device, basic safety precautions should always be followed, Read all instructions 
before using your desk.

FAILURE TO COMPLY WITH OR OBSERVE ALL INSTRUCTIONS AND WARNINGS REGARDING THE USE 
OF THIS PRODUCT MAY RESULT IN SERIOUS PROPERTY DAMAGE OR BODILY INJURY.
DANGER!

 To reduce the risk of electric shock, always unplug this device from the electrical outlet before cleaning 

or putting on or taking off parts.

 Keep children away from the electric height-adjustable desk control units and keypads.

 Use this desk only for its intended use as described in these instructions. Do not use attachments not 

 recommended by the manufacturer.

 Keep the desk close to the power socket/outlet to be easily accessible.

 Keep all electrical components away from liquids.

 Keep the cords away from heated surfaces.

 Never operate this desk if it (1) has a damaged cord or plug, (2) is not working properly, (3) has been 

 dropped or damaged, or (4) has been dropped into water.

 Do not open any of the components (e.g.,legs, control box or keypad) Contact Manufacturer for support and

 repairs.

 Do not insert anything into any seam or opening, this will damage the product.

 Do not operate this electrical product where aerosol (spray) products are being used or where oxygen is 

 being administered.

 Do not use outdoors.

 Ensure there are no obstacles around or under your desk before use to prevent crushing or trapping people 

 or property.

 Check the length of power cords for any electric devices placed on the desk before adjusting your desks

 height. Monitors, computer towers, speakers and other device cords may be pulled off or damaged if the 

 cords are too short.

 Keep hands and fingers clear of areas where they may get pinched by the mechanism.

 Please ensure this manual is available to any user, installer, or support personnel that operates this product.

 

MAKE SURE NO OBSTACLES ARE IN THE DESK’S PATH AND ALL CORDS ARE OF 
APPROPRIATE LENGTH FOR DESK TRAVEL. FAILURE TO COMPLY WITH OR OBSERVE
ALL ASSEMBLY, SAFETY, OPERATION INSTRUCTIONS AND WARNINGS REGARDING 
THE USE OF THIS PRODUCT MAY RESULT IN SERIOUS PROPERTY DAMAGE OR 
BODILY INJURY.

WARNING! To reduce the risk of burns, fire, electric shock or injury:

1. SAFETY AND WARNINGS

USE & LIABILITY

•  This height-adjustable desk has an electric motor and is designed for use in dry working conditions only. 
•  The desk height can be positioned at the most ergonomically suitable height for the user. These desks are 
   designed only for the purposes included in this manual. 
•  The desk should not be used in environments with high humidity or dampness, as this will damage the product. 
    Any other use is at user’s own risk.
•  Do not crawl between or lie under the desk frame. Do not sit or stand on the desk frame.
•  Children should never use the desk unless they are supervised by adults.

LIABILITY: 

This Eureka Ergonomic product is backed by  

a Three-Year Limited Warranty

 and 

a 30-day 

Risk-Free Purchase Guarantee

. If it does not work the way we promised, we'll make it right. Under no 

circumstances does the manufacturer accept warranty claims or liability claims for damages caused from 
improper use or handling of the desk frame other than that which is described in this operation manual.

Summary of Contents for ERK-EDK-GD

















Reviews: