manualshive.com logo in svg

EUCHNER MGB2-L1, Operating Instructions Manual, Page: 36 / 60

Share
Download
EUCHNER MGB2-L1 Operating Instructions Manual Download Page 36

Operating Instructions Safety Systems
MGB2-L1…-BR.-… / MGB2-L2…-BR.-… and MGB2-L1…-BP.-… / MGB2-L2…-BP.-…

36

(translation of the original operating instructions) 2500233-04-10/21

13.8.  Notes on operation with control systems

Observe the following requirements for connection to safe control systems: 

General notes

 

Ì

Use a common power supply for the control system and the connected safety switches.

 

Ì

A pulsed power supply must not be used for UB. Tap the supply voltage directly from the power supply unit. If the power 

supply is connected to a terminal of a safe control system, this output must provide sufficient electrical current. 

 

Ì

The safety outputs (FO1A and FO1B) can be connected to the safe inputs of a control system. Prerequisite: the input 

must be suitable for pulsed safety signals (OSSD signals, e.g. from light grids). The control system must tolerate test 

pulses on the input signals. This normally can be set up by parameter assignment in the control system. Observe the 

notes of the control system manufacturer. For the pulse duration of your safety switch, refer to chapter 

16. Technical 

data on page 50

.

 

Ì

The inputs on a connected evaluation unit must be positive switching, as the two outputs on the safety switch deliver a 

level of +24 V in the switched-on state.

BR

 

Ì

Always connect inputs FI1A and FI1B directly to a power supply unit or to outputs FO1A and FO1B of another 

EUCHNER BR device (series connection). Pulsed signals must not be present at inputs FI1A and FI1B. 

Guard locking control

 

Ì

Test pulses up to max. 5 ms in duration at intervals of min. 100 ms are tolerated on IMP and IMM.

NOTICE

Due to the fact that short circuit monitoring of the safety outputs FO1A/FO1B is performed by the 

device itself, the Performance Level in accordance with EN 13849 is not reduced if the control system 

pulsing is switched off.

Tip!

A detailed example of connecting and setting the parameters of the control system is available for 

many devices at www.euchner.com, in the area 

Downloads/Applications/MGB2

. The features of the 

respective device are dealt with there in greater detail.

Summary of Contents for MGB2-L1





























































Reviews:

No comments