manualshive.com logo in svg

EUCHNER CES-I-BR Series, Operating Instructions Manual

Share
Download
EUCHNER CES-I-BR Series Operating Instructions Manual Download Page 8

Operating Instructions

Non-Contact Safety Switch CES-I-BR-.-C07-…

8

(translation of the original operating instructions) 2510145-02-07/18

7.  Installation

CAUTION

Safety switches must not be bypassed (bridging of contacts), turned away, removed or otherwise 

rendered ineffective.

 

Ì

Observe EN ISO 14119:2013, section 7, for information about reducing the possibilities for by-

passing an interlocking device.

NOTICE

Risk of damage to equipment and malfunctions as a result of incorrect installation. 

 

Ì

Safety switches and actuators must not be used as an end stop.

 

Ì

Observe EN ISO 14119:2013, sections 5.2 and 5.3, for information about fastening the safety 

switch and the actuator.

 

Ì

From the assured switch-off distance S

ar

, the safety outputs are safely shut down.

 

Ì

When mounting several safety switches, observe the stipulated minimum distance to avoid mutual 
interference.

.

min. 140 mm

 

Ì

The operating distance changes during the mounting of the actuator as a function of the material 
used for the guard.

 

Ì

Observe direction of arrow on the device (see figure below).

Permissible approach directions

B

A

C

D

z

x

y

x

z

y

B

A

C

D

z

x

y

x

z

y

Note the following points:

 

Ì

Actuator and safety switch must be easily accessible for inspection and replacement.

 

Ì

Actuator and safety switch must be fitted so that

 -a minimum distance is maintained with a side approach direction to avoid entering the area of possible side lobes. See 

chapter 11. Technical data, section Typical operating distance for the related actuator.

 -when the guard is open up to the distance S

ar

 (assured switch-off distance), a hazard is excluded.

 -the actuator is positively mounted on the guard, e.g. by using the safety screws included.

 -they cannot be removed or tampered with using simple means. 

 

Ì

Pay attention to the maximum tightening torque for the read head or safety switch and actuator mountings of 0.8 Nm.

 

Ì

Seal the mounting holes after mounting using the caps provided to prevent the accumulation of dirt.

 

Ì

In order to avoid damage, the connection cable must be laid with protection in areas in which high-pressure cleaners are 

used.

Summary of Contents for CES-I-BR Series

































Reviews:

No comments

Brands by name

Popular brands

Load more brands