DALI&0/1-10V Constant Voltage Dimming Driver
2/2
User’s manual: 2019-9
www.euchips.com
DALI Wiring
※
The contents of this manual are updated without prior notice. If the function of the product you are using is inconsistent with the instructions,
the function of the product shall prevail.Please contact us if you have any questions .
Cautions
1.This product should be installed by qualified personnel.
2.This product is non waterproof, need to avoid sun and rain.In case of outdoor use, please ensure it is mounted in a water proof enclosure.
3.Good heat dissipation conditions extend product life. Please install the product in a well-ventilated environment.
4.Please make sure LED power supply output voltage, current is used to meet the product requirements.
5.Please ensure that adequate sized cable is used from the controller to the LED lights to carry the current. Please also ensure that the cable is secured tightly in the connector.
6.Due to safety concerns, PVC or rubber cord of 0.75- 2.5mm
²
is recommended for input and output terminal(s)(excluding signal terminals). Flat power cord is not suitable.Ensure all wire
connections and polarities are correct before applying power to avoid any damages to the LED lights.
7.In case of malfunction, do not repair it yourself.
Push DIM(Touch DIM) Diagram
DALI Diagram
Remark: Only use open push button without indicator light. Maximum cable length between each Unit: 20 meters.
Push DIM Function
1. Press the Push DIM (Touch DIM) switch for 8s or more,the driver can be controlled via Push DIM switch.
2. Short press the Push DIM (Touch DIM) switch (<0.5s) to control the lamp on or off.
3. Long press the Push DIM (Touch DIM) switch (>0.5s) to dim the brightness of light. The dimming direction will change every time after pressing switch.
4. Double-click the Push DIM (Touch DIM) switch (<0.3s), then all lamps connected on the device will be set maximum brightness.
5. The brightness adjustment range is 1%-100%, and the light can be turned off through short pressing when doing the adjustment with long pressing
Push DIM (Touch DIM) switch.
6. With the Power off memory function, the power-down state will be recovered when power on again.
Dimming Curve
DALI MASTER
N
L
0/1-10V Signal Input
N
L
DALI Curve
0/1-10V Curve
0
1
20
40
60
80
100
120
140
160
180
200
220
240 254
20
40
60
80
100
120
0
1
10
20
30
40
50
0.1
0.2
0.3
0.4
DALI Dimming Level
Output Current(%)
DALI Driver 1
DA
DA
LED+
LED-
L
N
DALI Driver 1
DA
DA
LED+
LED-
L
N
DALI Driver 1
DA
DA
LED+
LED-
L
N
Push DIM Panel(Touch DIM)
L
N
86
1
86
1
86
1
12V/24V
86
1
86
1
86
1
12V/24V
86
1
86
1
86
1
12V/24V
DALI Driver 1
DA
DA
LED+
LED-
L
N
DALI Driver 1
DA
DA
LED+
LED-
L
N
DALI Driver 1
DA
DA
LED+
LED-
L
N
L
N
DALI Controller
86
1
86
1
86
1
12V/24V
86
1
86
1
86
1
12V/24V
86
1
86
1
86
1
12V/24V
100
80
60
40
20
0
0
5 9 14 18 23 27 32 36 41 45 50 54 59 63 68 72 77 81 86 90 95 99
Input Signal(%)
Output Voltage(%)
