background image

                                                                                                                   

SHANGHAI EUCHIPS INDUSTRIAL CO.,LTD

 

EUP12R-1WMC-0    User Manual V01.1   

                                                          4                                                                       

www.euchips.com 

 

 

Button Functions: 

1

ALL ON/ALL OFF:

 Press the button to turn on or turn off the led driver which be matched to this remote. 

2

Bri/Brightness-:

 Adjust the LED lights brightness. Press and hold to adjust quickly. 

3

Highest Brightness /Lowest Brightness: 

Set brightness to highest level or lowest level directly.   

4

Group ON/Group OFF: 

Press the button to turn on or turn off the lights which be matched to this group. 

 

Match code and grouping

 

The remote control can be used after the remote match the code with the led driver, the method is as following: 

Choose the led driver that you want to divide the group, then turn off the power for 10 seconds, then turn on the 

power switch, at the same time when you turn on the power (in 3 seconds), press the button "Group ON" of the group 

you want. The lights connecting to the driver will flick for 3 times, and then this group is set successfully. The other 

groups can also be set by the same method. 

Remark

One led driver can only match one group of the same remote, but one remote group can match countless 

led drivers, and one led driver can match 10 remotes. 

 

Clear code and regroup: 

If the room layout are changed, or you want to make a little adjustment upon your fond, then you may want to change 

the previous groups. Before regrouping, you need to clear the code, the method is as following: 

Full clear code

Choose the led driver you want to clear the code

If more than one driver needs to be clear, the 

operation is performed at the same time.

, turn off the power for 10 seconds, then turn on the power again. Within 3 

seconds, press the " All ON " button quickly for 6 times, the lamp connected to the LED driver will flick quickly for 6 

times, then the code is cleared successfully, and it can

’t be controlled by all the remote control. 

Group clear code

If you do not need to regroup, only clear code for a group of remote control, choose the led driver 

you want to clear the code

If more than one driver needs to be clear, the operation is performed at the same time.

turn off the power for 10 seconds, then turn on the power again. Within 3 seconds, press the corresponding "Group 

ON " button quickly for 6 times, the lamp connected to the LED driver will flick quickly for 6 times, then the code is 

cleared successfully, but it can be controlled by other remote controls. 

After the code is cleared, the method of setting the group is totally the same as the principle of "matching the code 

and grouping" 

Remark

The remote should not put in the area with large-scale metal or near strong electromagnetic wave region; 

otherwise the communication distance will be seriously affected. 

Summary of Contents for EUP12R-1WMC-0

Page 1: ... remote RC14 or RC11 to dim lightings Each driver could at the same time be matched and controlled by 10 remotes and one remote can match unlimited drivers Product Features Single channel output output current level selectable by DIP S W Using 2 4GHz RF remote control Wide range of input voltage 100VAC 240VAC High efficiency up to 82 Built in active PFC function Dimming effect smooth no flicker Pr...

Page 2: ...ncy 82 230VAC full load Current 0 1Amax 230VAC Inrush current 15A 230VAC Protection Short circuit Close output recovers automatically after fault removed Function Dimming 2 4GHz RF remote control Optional remote control RC14 RC11 Others Dimension 150 43 29 mm L W H G W 120g Working temp 20 40 Relative humidity 20 90 RH Dimension mm Current Selection Table EUP12R 1WMC 0 is a multi current dimming d...

Page 3: ...lease ensure good ventilation 4 Please check if the output voltage and current of any LED power supplies used comply with the requirement of the product 5 Please ensure that adequate sized cable is used from the controller to the LED lights to carry the current Please also ensure that the cable is secured tightly in the connector 6 Ensure all wire connections and polarities are correct before appl...

Page 4: ... want to make a little adjustment upon your fond then you may want to change the previous groups Before regrouping you need to clear the code the method is as following Full clear code Choose the led driver you want to clear the code If more than one driver needs to be clear the operation is performed at the same time turn off the power for 10 seconds then turn on the power again Within 3 seconds ...

Reviews: