ETS-Lindgren HI-3638 User Manual Download Page 39 | Manualshive

Page: 39 / 41

ETS-Lindgren HI-3638 User Manual Download Page 39

www.ets-lindgren.com References

39

MPR (1987). Testing Visual Display Units-test methods, MPR-P 1987:2, National
Council for Metrology and Testing, Stockholm, Sweden, May 15, 1987.

NATO (1979). Control and recording of personnel exposure to radio-frequency
radiation. Standardization Agreement STANAG No. 2345, February 16.

Nylen, P., U. Bergqvist, R. Wibom and B. Knave (1984). Indoor air: Swedish
Council for Building Research, 3, pp. 163-167.

Olsen, W.C. (1981). Electric field enhanced aerosol exposure in visual display
environments. Prepared for the Norwegian Directorate of Labor Inspection.
CMI No. 803604-1.

Paulsson, L.E., et al., (1984). Stralning fran dataskarmar. Report a 84-08,
National Institute for Radiation Protection, Stockholm, Sweden, February 4.

Petersen, R.C., M.M. Weiss and G. Minneci (1980). Nonionizing electromagnetic
radiation associated with video-display terminals, Ocular Effects of Non-ionizing
Radiation, Vol (229) SPIE (Society of Photo-Optical Instrumentation Engineers),
Box 10, Bellingham, Washington 98227 USA, pp. 179-186.

Roy, C.R., et al., (1983). Measurement of electromagnetic radiation emitted from
visual display terminals (VDTs). Australian Radiation Laboratory
report ARL/TR053, Yallambie, Victoria, March.

Slesin, L. (1985). New Soviet Population Standard: 10 uW/cm2 at MW
frequencies. Microwave News (V), 5, June, pp. 1-5.

Stuchly, M.A., D.W. Lecuyer and R.D. Mann (1983). Extremely low frequency
electromagnetic emissions from video display terminals and other devices.
Health Physics, (45), No. 3 (September), pp. 713-722.

Telecom (1984). Telecom Australia occupational health policy & guidelines
screen based equipment. Telecom internal guideline 15.1, Melbourne, Victoria,
September.

Tell, R.A. (1983). Instrumentation for measurement of electromagnetic fields:
equipment, calibration, and selected applications. In Biological Effects and
Dosimetry of Nonionizing Radiation, (Eds., M. Grandolgo, S. Michaelson, and
A. Rindi), NATO Advance Study Institute Series, Series A.: Life Sciences,
Vol. 49, Plenum Publishing Company.

«
...
37
38
39
40
41
»

Summary of Contents for HI-3638










































Reviews:

No comments