manualshive.com logo in svg

ETS-Lindgren EMCenter, User Manual

Share
Download
ETS-Lindgren EMCenter User Manual Download Page 3

www.ets-lindgren.com 

iii

 

 

Table of Contents 

 

Notes, Cautions, and Warnings ............................................... vi

 

1.0 Introduction .......................................................................... 7

 

EMCenter Plug-In Cards (Optional) ............................................................................... 8

 

EMSwitch RF Switch Plug-In Card ........................................................ 8

 

EMPower Plug-In Card and EMPower Sensors .................................... 9

 

EMControl Positioner Control Plug-In Card ......................................... 10

 

EMSense EMF Probe Plug-In Card ..................................................... 10

 

EMGen RF Signal Generator Plug-In Card ......................................... 11

 

Standard Configuration ................................................................................................ 11

 

ETS-Lindgren Product Information Bulletin .................................................................. 12

 

2.0 Maintenance ....................................................................... 13

 

Maintenance of Fiber Optics ........................................................................................ 14

 

Service Procedures ...................................................................................................... 14

 

3.0 Specifications ..................................................................... 15

 

Performance Specifications ......................................................................................... 15

 

Physical Specifications ................................................................................................ 15

 

Environmental Specifications ....................................................................................... 15

 

Power Specifications .................................................................................................... 16

 

Interface and Cable Specifications .............................................................................. 16

 

4.0 Laser Safety ........................................................................ 17

 

Safety Precautions ....................................................................................................... 17

 

Safety Features ............................................................................................................ 18

 

5.0 EMCenter Controls and Connectors ................................ 19

 

Front Panel .................................................................................................................. 19

 

Summary of Contents for EMCenter












































Reviews:

No comments

Brands by name

Popular brands

Load more brands