background image

Page 4 of 16 

 

ETM9900(J) Quick Start Guide Issue 27012009 

Introduction 

Nomenclature 

ETM9900 incorporates the Siemens HC25 engine and is intended for use within Australia, NZ and 
worldwide. 
 
The ETM9900J variant incorporates the Siemens HC28 engine and is intended for use within 
Japan on the Softbank network and global roaming. 

Overview. 

The ETM9900(J) is an industrial terminal designed for M2M (Machine to Machine) communications. 
With Tri-band UMTS/HSDPA and Quad-Band GSM/GPRS/EDGE capability, the ETM9900(J) has 
the versatility to operate on virtually any GSM or UMTS network. 

 

Terminal Nomenclature/History 
Model 

Comment 

Module Installed 

ETM9900 

First Release 

HC25 Release 1.0, 1.2, 1.78 or 
2.05 

ETM9900-1 

Future Release 

HC25 Release 2.05, 7 x I/O’s 
versus 4 x I/O’s for ETM9900 

ETM9900J 

First Release Japan only unit 

HC28, 7 x I/O’s 

 

Module Nomenclature/History 
Model 

Comment 

HC25 Release 1.0/1.2 

Initial release 

HC25 Release 1.78 

Maintenance Release Australia and New Zealand Only 

HC25 Release 2.05 

Current Release 

HC28 Release 1.03 

Current Release 

 

Applications 

Typical applications include: 

◩ 

Security; 

◩ 

Automated Meter Reading (Telemetry); 

◩ 

Interface to data acquisition/data logging systems; 

◩ 

Broadcasting/updating multi-media files; 

◩ 

Interfacing with alarm and control applications. 

Interfaces 

◩ 

RJ12 power connector 

◩ 

RJ45 I/O connector 

◩ 

RS232 interface (V.24/V.28 on the D-Sub socket)  

◩ 

Antenna connector SMA Jack (female)  

◩ 

Mini-SIM card holder 

Summary of Contents for ETM9900(J)

















Reviews: