manualshive.com logo in svg

EtherWAN EX24000, User Manual

Share
Download
EtherWAN EX24000 User Manual Download Page 69

 

 

Removing a Static MAC Address from a Port 

To remove a static MAC entry for a particular port (see 

Figure 28

): 

1.  For a particular port, select the MAC address to be deleted from the 

Delete MAC 

Address

 drop down box.  

2.  Click on the 

Submit

 button. 

 

 

Figure 28: Removing a Static MAC 

 

Adding a MAC to the Static-MAC-Entry Discard Table 

To add a MAC address to the 

Static-MAC-Entry Discard

 table (see 

Figure 29

): 

1.  Enter a MAC address in the form “0000.1234.abdc” in the 

Add MAC Address

 text 

box of the 

Static-MAC-Entry-Discard

 section. 

2.  Select the VLAN associated with the MAC address. 

3.  It should be noted that while static MAC address for forwarding are associated with 

the switch on a per-port basis. Static MAC discards are associated with the switch for 
all ports.  

4.  Click on the 

Submit

 button. 

69 

EX24000 Switch Users Guide 

Summary of Contents for EX24000
















































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands