manualshive.com logo in svg

EtherWAN EX24000, User Manual

Share
Download
EtherWAN EX24000 User Manual Download Page 175

 

To enable the 802.1X function globally on the switch:  

1. Choose 

enable

 from the drop down list next to 

Radius Status

 

2.  Click on the 

Update Setting

 button. (See 

Figure 87

) 

 

 

Figure 87: Enable Radius

 

 

Adding a Radius Server 

Next, you will need to configure the settings that the switch will need in order to connect to a 
RADIUS server.  

1.  Click on the 

Add Radius

 button (see 

如上

). 

2.  Next, enter the IP address of the RADIUS server that the switch will use in order to 

authenticate in the text entry box next to 

Radius Server IP

 (see 

Figure 88

).  

3.  Enter the password for RADIUS server in the text entry box next to 

Secret Key

. 

4.   Optionally, the UDP port number for the RADIUS server (if it is different from the 

standard default 1812) can be changed. To do this, enter the port number in the text 
entry box next to 

Radius Server Port

.  

5.  Next, you can choose to configure the minimum time that the switch must wait, 

before it is allowed to retransmit a message to the RADIUS server due to no 
response. To do this, enter the number of seconds that the switch must wait 
(between 1 and 1000 seconds) into the text entry box next to 

Timeout <1-1000>

 .  

175 

EX24000 Switch Users Guide 

Summary of Contents for EX24000
















































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands