manualshive.com logo in svg

EtherWAN EX24000, User Manual

Share
Download
EtherWAN EX24000 User Manual Download Page 107

 

 

Setting Bridge Priority 

To set the Bridge Priority: 

1. Enter the 

Bridge Priority ID

 in the text box to the right of 

Bridge Priority 

(0..61440)

 

2.  Click on the 

Update Setting 

button. 

 Note:

 The valid values for this parameter are from 0 to 61440, in increments of 

4096; you will see this value reflected in the first hexadecimal digit of the 

Bridge ID

 field 

after you click the 

Update Setting

 button (See 

Figure 48

). Set this value to be less than 

any other switch on the network, in order to make this switch the Root Switch. To set a 

Backup Root Bridge

 set the 

Bridge ID

 to be between the 

Root Bridge

 and the rest of 

the network switches. 

 

 

Figure 48: Bridge ID Display

 

 

107 

EX24000 Switch Users Guide 

Summary of Contents for EX24000
















































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands