ED3538 10/100Base-TX Hardened PoL/PoE Ethernet Extender over Copper Wires www.etherwan.com
2
70G-ED3538XQ2
Operating temperature range @ -40
to 75
(
℃
℃
-40
℉
to 167
℉
). Tested for functional operation @ -40
to 85
℃
℃
(-40
℉
to 185
℉
).
Ethernet port: Supports IEEE802.3/802.3u/802.3x. Auto-negotiation: 10/100Mbps, full/half-duplex; Auto
MDI/MDIX.
10/100Base-TX Connection
The following lists the pinouts of
10/100Base-TX RJ-45 port.
Pin
Regular Port
PoE Port
1
Output Transmit Data +
Output Transmit Data +
2
Output Transmit Data -
Output Transmit Data -
3
Input Receive Data +
Input Receive Data +
4
Positive
(VCC+)
5
Positive
(VCC+)
6
Input Receive Data -
Input Receive Data -
7
Negative
(VCC-)
8
Negative
(VCC-)
Supports Power over Ethernet application up to 1,200meters (3,937ft.) for Max. 5 watts power consumed PoE
powered devices.
Power Supply: Redundant T: 46-57V, R: 46-57V DC Terminal Block power inputs and 48VDC Latched DC JACK
interface.
Six speeds with speed indicator LEDs on front panel of unit, up to 100Mbps @ about 300meters (984ft.), down to
1Mbps @ about 2,200meters (7,218ft.).
Ethernet Extender Connection
The RJ-11 and Terminal Block port pinouts
Pin 3: Tip, Pin 4: Ring.
Use a telephone line to connect two RJ-11 or
Terminal Block ports between two Hardened
Ethernet Extenders.
Max.
5W
without
PoE
output.
Meets EN61000-6-2 & EN61000-6-4 EMC Generic Standard Immunity for industrial environment.
10/100Base-TX and Ethernet Extender Connectors
Power
consumption:
- Enable
Power over Link (PoL) function: Max. 65Watts
- Disable
Power over Link (PoL) function: ED3538T: Max. 5W
ED3538R: Max. 35W with PoE output
Auto data rate negotiation for Ethernet extension interface.
Supports Din-Rail or Panel Mounting installation.
Power Input Assignment
Power1 48VDC
DC
Jack
＋
T: 46-57VDC
R: 46-57VDC
Power2
－
Power Ground
＋
T: 46-57VDC
R: 46-57VDC
Power3
－
Power Ground
Terminal
Block
DIP
Switch
Down Up
ED3538T
PoL
Disable Power over Link
Enable Power over Link
Type
Std (Standard)
Standard line speed
Better noise immunity
Perf (Performance)
Better line speed
Poor noise immunity
ED3538R
Mode
Loc (Local), Set
ED3538R to Local Mode
Rmt (Remote), Set
ED3538R to Remote Mode
Type
Std (Standard)
Standard line speed
Better noise immunity
Perf (Performance)
Better line speed
Poor noise immunity
LEDs State Indication
Steady Power
received
Power 1/2/3
Off Power
off
Steady
Power Ethernet extension interface function is enabled
PoL
Off
No power is transmitted over Ethernet extension interface
Steady
Powered device (PD) is connected
PoE
Off
Powered device (PD) is disconnected
Steady
A valid Extender connection established
Fast Flashing
Data transmission or receiving
Slow Flashing
Extender port under negotiation mode
Link
Off
Extender interface connection is not established
Line Speed
Steady
Displays the link speed in Mbps
Steady
PoE power can be transmitted for PD
PSE Output
All off
No PoE power can be transmitted for PD
Steady
A valid Ethernet connection established
Flashing Data
transmission or receiving
Green
Off
Non-Ethernet connection is established
Steady
Link speed at 100Mbps
Yellow
Off
Link speed at 10Mbps
Power over Link
(PoL)
Enabled
Distance Data Rate ED3538R PoE Output
300M 100Mbps
30.0W
400M 90Mbps 15.4W
600M 60Mbps 14.0W
800M 45Mbps 9.5W
1000M 35Mbps 7.0W
1200M 20Mbps 5.0W
Power over Link
(PoL)
Disabled
Power Supply Applied on ED3538R
Distance Data
Rate
ED3538R PoE
Output
1400M 15Mbps
30.0W
1600M 10Mbps
30.0W
1800M 3Mbps
30.0W
Up to 2200M 1Mbps
30.0W
<Note>
The Reference Performance is tested on 24AWG Telephone wire (0.5mm diameter, 1-pair wire, Cable impedance:
100ohm).
Functional Description
