Eteros Mobius User Manual Download Page 15

15

MOBIUSTRIMMER.COM

CLEANING

With the exception of the electrical enclosure, the MOBIUS AUTOMATIC TUMBLER AND BRUSH WASHER 

can be washed, cleaned, and wiped down with normal detergents, degreasers, and disinfectants.

The lid and facias can be removed to facilitate cleaning. The inside of the MTB WASHER can be washed 

and wiped as needed.  

The exterior of the MTB WASHER can be hosed or sprayed, except in the control panel area. Evidence 

of water near the electrical panel could void the machine warranty.

The machine is easily moved and rolled on level surfaces. The machine includes four locking swivel 

casters that are installed at the factory. The machine is designed to be operated on smooth and level 

floors. 

If lifting is required, the MOBIUS AUTOMATIC TUMBLER AND BRUSH WASHER must be lifted using a forklift 

on the lower surface of the body. Ensure that the forks are fully spread to avoid overturning or flipping 

off the forks. 

DO NOT LIFT FROM THE STRUTS AT THE BOTTOM OF THE MACHINE.

The MOBIUS AUTOMATIC TUMBLER AND BRUSH WASHER is largely maintenance-free. 

The components that support the spreader shaft are the only parts that may experience wear. The 

condition of these surfaces should be inspected before each use. If you begin to notice galling on 

the stainless-steel surface or significant wear of the plastic surfaces, contact ETEROS TECHNOLOGIES to 

obtain a replacement component. 

This User Guide does not include instructions for machine repair. For your safety, repairs must be 

completed by ETEROS TECHNOLOGIES or an authorized agent (service technician).

Should repairs be required, please contact:

ETEROS TECHNOLOGIES 

502-130 INDUSTRIAL AVE. 

CARLETON PLACE, ONTARIO, CANADA 

K7C 3T2 

 

www.ETEROS.com 

Improper interfacing, improper repair, or unauthorized modification could result in void warranty claims.

MAINTENANCE

LIFTING AND MOVING

ENSURE THAT THE MOBIUS AUTOMATIC TUMBLER AND BRUSH WASHER 

IS LOCKED OUT BEFORE PERFORMING ANY SETUP OR MAINTENANCE.

Summary of Contents for Mobius


















Reviews: