Eternus DX80 S2 User Manual Download Page 47 | Manualshive

Page: 47 / 71

background image

Chapter 3 Connections
3.1 Host Connections

ETERNUS DX80 S2/DX90 S2 Disk storage system User’s Guide -Site Planning-

47

Copyright 2011 FUJITSU LIMITED

P3AM-4822-03ENZ0

If a path fails, access can continue by using the path failover function that switches access from
the failed path to another path. The performance of the system can be improved by using the
load balancing function to spread the access load over multiple paths.

Figure 3.3

Multipath connection (direct connection)

Figure 3.4

Multipath connection (switch connection)

•

When configuring multipathing for reliability, make sure to configure a
redundant connection for the controllers of the ETERNUS DX Disk
storage system. Configure paths to connect to different controllers
(CM#0 and CM#1). Combinations of host interface adapter numbers
(CA#0 and CA#1) in controllers do not need to be taken into
consideration.

•

Paths from a single server should be separately connected to a different
host interface adapter in case of host interface adapter failure.

Server

HBA

HBA

Server

HBA

HBA

ETERNUS DX Disk storage system

Port

CA

Port

CM#0

Port

CA

Port

Port

CA

Port

Port

CA

Port

CM#1

Server

HBA

HBA

Server

HBA

HBA

Server

HBA

HBA

Switch

Switch

ETERNUS DX Disk storage system

CM#0

Port

CA

Port

Port

CA

Port

CM#1

«
...
45
46
47
48
49
...
»

Summary of Contents for DX80 S2








































































Reviews:

No comments

Related manuals for DX80 S2

Brand: Park Tool Pages: 2

Brand: Gearwrench Pages: 9

Brand: IBM Pages: 188

Brand: Dorel Asia Pages: 15

Brand: Maxtor Pages: 50

Brand: DataWhale Pages: 31

StorNext QD7000

Brand: Quantum Pages: 29

Brand: LaCie Pages: 27

ReadyNAS 3220 Series

Brand: NETGEAR Pages: 4

Brand: Glyph Pages: 7

DURAMAX Apex Pro 10.5 Ft x 8 Ft 40116

Brand: USP Pages: 79

URBAN 100.1P DEC

Brand: garofalo Pages: 16

Brand: AEG Pages: 16

Brand: Samsung Pages: 2

Brand: Samsung Pages: 4

Brand: Samsung Pages: 6

Brand: Samsung Pages: 43

Brand: Samsung Pages: 60

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands